MINI Sh3ll
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* Copyright (c) by Jaroslav Kysela <[email protected]>,
* Creative Labs, Inc.
* Definitions for EMU10K1 (SB Live!) chips
*/
#ifndef __SOUND_EMU10K1_H
#define __SOUND_EMU10K1_H
#include <sound/pcm.h>
#include <sound/rawmidi.h>
#include <sound/hwdep.h>
#include <sound/ac97_codec.h>
#include <sound/util_mem.h>
#include <sound/pcm-indirect.h>
#include <sound/timer.h>
#include <linux/interrupt.h>
#include <linux/mutex.h>
#include <linux/firmware.h>
#include <linux/io.h>
#include <uapi/sound/emu10k1.h>
/* ------------------- DEFINES -------------------- */
#define EMUPAGESIZE 4096
#define MAXREQVOICES 8
#define MAXPAGES0 4096 /* 32 bit mode */
#define MAXPAGES1 8192 /* 31 bit mode */
#define RESERVED 0
#define NUM_MIDI 16
#define NUM_G 64 /* use all channels */
#define NUM_FXSENDS 4
#define NUM_EFX_PLAYBACK 16
/* FIXME? - according to the OSS driver the EMU10K1 needs a 29 bit DMA mask */
#define EMU10K1_DMA_MASK 0x7fffffffUL /* 31bit */
#define AUDIGY_DMA_MASK 0xffffffffUL /* 32bit mode */
#define TMEMSIZE 256*1024
#define TMEMSIZEREG 4
#define IP_TO_CP(ip) ((ip == 0) ? 0 : (((0x00001000uL | (ip & 0x00000FFFL)) << (((ip >> 12) & 0x000FL) + 4)) & 0xFFFF0000uL))
// Audigy specify registers are prefixed with 'A_'
/************************************************************************************************/
/* PCI function 0 registers, address = <val> + PCIBASE0 */
/************************************************************************************************/
#define PTR 0x00 /* Indexed register set pointer register */
/* NOTE: The CHANNELNUM and ADDRESS words can */
/* be modified independently of each other. */
#define PTR_CHANNELNUM_MASK 0x0000003f /* For each per-channel register, indicates the */
/* channel number of the register to be */
/* accessed. For non per-channel registers the */
/* value should be set to zero. */
#define PTR_ADDRESS_MASK 0x07ff0000 /* Register index */
#define A_PTR_ADDRESS_MASK 0x0fff0000
#define DATA 0x04 /* Indexed register set data register */
#define IPR 0x08 /* Global interrupt pending register */
/* Clear pending interrupts by writing a 1 to */
/* the relevant bits and zero to the other bits */
#define IPR_P16V 0x80000000 /* Bit set when the CA0151 P16V chip wishes
to interrupt */
#define IPR_GPIOMSG 0x20000000 /* GPIO message interrupt (RE'd, still not sure
which INTE bits enable it) */
/* The next two interrupts are for the midi port on the Audigy Drive (A_MPU1) */
#define IPR_A_MIDITRANSBUFEMPTY2 0x10000000 /* MIDI UART transmit buffer empty */
#define IPR_A_MIDIRECVBUFEMPTY2 0x08000000 /* MIDI UART receive buffer empty */
#define IPR_SPDIFBUFFULL 0x04000000 /* SPDIF capture related, 10k2 only? (RE) */
#define IPR_SPDIFBUFHALFFULL 0x02000000 /* SPDIF capture related? (RE) */
#define IPR_SAMPLERATETRACKER 0x01000000 /* Sample rate tracker lock status change */
#define IPR_FXDSP 0x00800000 /* Enable FX DSP interrupts */
#define IPR_FORCEINT 0x00400000 /* Force Sound Blaster interrupt */
#define IPR_PCIERROR 0x00200000 /* PCI bus error */
#define IPR_VOLINCR 0x00100000 /* Volume increment button pressed */
#define IPR_VOLDECR 0x00080000 /* Volume decrement button pressed */
#define IPR_MUTE 0x00040000 /* Mute button pressed */
#define IPR_MICBUFFULL 0x00020000 /* Microphone buffer full */
#define IPR_MICBUFHALFFULL 0x00010000 /* Microphone buffer half full */
#define IPR_ADCBUFFULL 0x00008000 /* ADC buffer full */
#define IPR_ADCBUFHALFFULL 0x00004000 /* ADC buffer half full */
#define IPR_EFXBUFFULL 0x00002000 /* Effects buffer full */
#define IPR_EFXBUFHALFFULL 0x00001000 /* Effects buffer half full */
#define IPR_GPSPDIFSTATUSCHANGE 0x00000800 /* GPSPDIF channel status change */
#define IPR_CDROMSTATUSCHANGE 0x00000400 /* CD-ROM channel status change */
#define IPR_INTERVALTIMER 0x00000200 /* Interval timer terminal count */
#define IPR_MIDITRANSBUFEMPTY 0x00000100 /* MIDI UART transmit buffer empty */
#define IPR_MIDIRECVBUFEMPTY 0x00000080 /* MIDI UART receive buffer empty */
#define IPR_CHANNELLOOP 0x00000040 /* Channel (half) loop interrupt(s) pending */
#define IPR_CHANNELNUMBERMASK 0x0000003f /* When IPR_CHANNELLOOP is set, indicates the */
/* highest set channel in CLIPL, CLIPH, HLIPL, */
/* or HLIPH. When IP is written with CL set, */
/* the bit in H/CLIPL or H/CLIPH corresponding */
/* to the CIN value written will be cleared. */
#define INTE 0x0c /* Interrupt enable register */
#define INTE_VIRTUALSB_MASK 0xc0000000 /* Virtual Soundblaster I/O port capture */
#define INTE_VIRTUALSB_220 0x00000000 /* Capture at I/O base address 0x220-0x22f */
#define INTE_VIRTUALSB_240 0x40000000 /* Capture at I/O base address 0x240 */
#define INTE_VIRTUALSB_260 0x80000000 /* Capture at I/O base address 0x260 */
#define INTE_VIRTUALSB_280 0xc0000000 /* Capture at I/O base address 0x280 */
#define INTE_VIRTUALMPU_MASK 0x30000000 /* Virtual MPU I/O port capture */
#define INTE_VIRTUALMPU_300 0x00000000 /* Capture at I/O base address 0x300-0x301 */
#define INTE_VIRTUALMPU_310 0x10000000 /* Capture at I/O base address 0x310 */
#define INTE_VIRTUALMPU_320 0x20000000 /* Capture at I/O base address 0x320 */
#define INTE_VIRTUALMPU_330 0x30000000 /* Capture at I/O base address 0x330 */
#define INTE_MASTERDMAENABLE 0x08000000 /* Master DMA emulation at 0x000-0x00f */
#define INTE_SLAVEDMAENABLE 0x04000000 /* Slave DMA emulation at 0x0c0-0x0df */
#define INTE_MASTERPICENABLE 0x02000000 /* Master PIC emulation at 0x020-0x021 */
#define INTE_SLAVEPICENABLE 0x01000000 /* Slave PIC emulation at 0x0a0-0x0a1 */
#define INTE_VSBENABLE 0x00800000 /* Enable virtual Soundblaster */
#define INTE_ADLIBENABLE 0x00400000 /* Enable AdLib emulation at 0x388-0x38b */
#define INTE_MPUENABLE 0x00200000 /* Enable virtual MPU */
#define INTE_FORCEINT 0x00100000 /* Continuously assert INTAN */
#define INTE_MRHANDENABLE 0x00080000 /* Enable the "Mr. Hand" logic */
/* NOTE: There is no reason to use this under */
/* Linux, and it will cause odd hardware */
/* behavior and possibly random segfaults and */
/* lockups if enabled. */
/* The next two interrupts are for the midi port on the Audigy Drive (A_MPU1) */
#define INTE_A_MIDITXENABLE2 0x00020000 /* Enable MIDI transmit-buffer-empty interrupts */
#define INTE_A_MIDIRXENABLE2 0x00010000 /* Enable MIDI receive-buffer-empty interrupts */
#define INTE_SAMPLERATETRACKER 0x00002000 /* Enable sample rate tracker interrupts */
/* NOTE: This bit must always be enabled */
#define INTE_FXDSPENABLE 0x00001000 /* Enable FX DSP interrupts */
#define INTE_PCIERRORENABLE 0x00000800 /* Enable PCI bus error interrupts */
#define INTE_VOLINCRENABLE 0x00000400 /* Enable volume increment button interrupts */
#define INTE_VOLDECRENABLE 0x00000200 /* Enable volume decrement button interrupts */
#define INTE_MUTEENABLE 0x00000100 /* Enable mute button interrupts */
#define INTE_MICBUFENABLE 0x00000080 /* Enable microphone buffer interrupts */
#define INTE_ADCBUFENABLE 0x00000040 /* Enable ADC buffer interrupts */
#define INTE_EFXBUFENABLE 0x00000020 /* Enable Effects buffer interrupts */
#define INTE_GPSPDIFENABLE 0x00000010 /* Enable GPSPDIF status interrupts */
#define INTE_CDSPDIFENABLE 0x00000008 /* Enable CDSPDIF status interrupts */
#define INTE_INTERVALTIMERENB 0x00000004 /* Enable interval timer interrupts */
#define INTE_MIDITXENABLE 0x00000002 /* Enable MIDI transmit-buffer-empty interrupts */
#define INTE_MIDIRXENABLE 0x00000001 /* Enable MIDI receive-buffer-empty interrupts */
#define WC 0x10 /* Wall Clock register */
#define WC_SAMPLECOUNTER_MASK 0x03FFFFC0 /* Sample periods elapsed since reset */
#define WC_SAMPLECOUNTER 0x14060010
#define WC_CURRENTCHANNEL 0x0000003F /* Channel [0..63] currently being serviced */
/* NOTE: Each channel takes 1/64th of a sample */
/* period to be serviced. */
#define HCFG 0x14 /* Hardware config register */
/* NOTE: There is no reason to use the legacy */
/* SoundBlaster emulation stuff described below */
/* under Linux, and all kinds of weird hardware */
/* behavior can result if you try. Don't. */
#define HCFG_LEGACYFUNC_MASK 0xe0000000 /* Legacy function number */
#define HCFG_LEGACYFUNC_MPU 0x00000000 /* Legacy MPU */
#define HCFG_LEGACYFUNC_SB 0x40000000 /* Legacy SB */
#define HCFG_LEGACYFUNC_AD 0x60000000 /* Legacy AD */
#define HCFG_LEGACYFUNC_MPIC 0x80000000 /* Legacy MPIC */
#define HCFG_LEGACYFUNC_MDMA 0xa0000000 /* Legacy MDMA */
#define HCFG_LEGACYFUNC_SPCI 0xc0000000 /* Legacy SPCI */
#define HCFG_LEGACYFUNC_SDMA 0xe0000000 /* Legacy SDMA */
#define HCFG_IOCAPTUREADDR 0x1f000000 /* The 4 LSBs of the captured I/O address. */
#define HCFG_LEGACYWRITE 0x00800000 /* 1 = write, 0 = read */
#define HCFG_LEGACYWORD 0x00400000 /* 1 = word, 0 = byte */
#define HCFG_LEGACYINT 0x00200000 /* 1 = legacy event captured. Write 1 to clear. */
/* NOTE: The rest of the bits in this register */
/* _are_ relevant under Linux. */
#define HCFG_PUSH_BUTTON_ENABLE 0x00100000 /* Enables Volume Inc/Dec and Mute functions */
#define HCFG_BAUD_RATE 0x00080000 /* 0 = 48kHz, 1 = 44.1kHz */
#define HCFG_EXPANDED_MEM 0x00040000 /* 1 = any 16M of 4G addr, 0 = 32M of 2G addr */
#define HCFG_CODECFORMAT_MASK 0x00030000 /* CODEC format */
/* Specific to Alice2, CA0102 */
#define HCFG_CODECFORMAT_AC97_1 0x00000000 /* AC97 CODEC format -- Ver 1.03 */
#define HCFG_CODECFORMAT_AC97_2 0x00010000 /* AC97 CODEC format -- Ver 2.1 */
#define HCFG_AUTOMUTE_ASYNC 0x00008000 /* When set, the async sample rate convertors */
/* will automatically mute their output when */
/* they are not rate-locked to the external */
/* async audio source */
#define HCFG_AUTOMUTE_SPDIF 0x00004000 /* When set, the async sample rate convertors */
/* will automatically mute their output when */
/* the SPDIF V-bit indicates invalid audio */
#define HCFG_EMU32_SLAVE 0x00002000 /* 0 = Master, 1 = Slave. Slave for EMU1010 */
#define HCFG_SLOW_RAMP 0x00001000 /* Increases Send Smoothing time constant */
/* 0x00000800 not used on Alice2 */
#define HCFG_PHASE_TRACK_MASK 0x00000700 /* When set, forces corresponding input to */
/* phase track the previous input. */
/* I2S0 can phase track the last S/PDIF input */
#define HCFG_I2S_ASRC_ENABLE 0x00000070 /* When set, enables asynchronous sample rate */
/* conversion for the corresponding */
/* I2S format input */
/* Rest of HCFG 0x0000000f same as below. LOCKSOUNDCACHE etc. */
/* Older chips */
#define HCFG_CODECFORMAT_AC97 0x00000000 /* AC97 CODEC format -- Primary Output */
#define HCFG_CODECFORMAT_I2S 0x00010000 /* I2S CODEC format -- Secondary (Rear) Output */
#define HCFG_GPINPUT0 0x00004000 /* External pin112 */
#define HCFG_GPINPUT1 0x00002000 /* External pin110 */
#define HCFG_GPOUTPUT_MASK 0x00001c00 /* External pins which may be controlled */
#define HCFG_GPOUT0 0x00001000 /* External pin? (spdif enable on 5.1) */
#define HCFG_GPOUT1 0x00000800 /* External pin? (IR) */
#define HCFG_GPOUT2 0x00000400 /* External pin? (IR) */
#define HCFG_JOYENABLE 0x00000200 /* Internal joystick enable */
#define HCFG_PHASETRACKENABLE 0x00000100 /* Phase tracking enable */
/* 1 = Force all 3 async digital inputs to use */
/* the same async sample rate tracker (ZVIDEO) */
#define HCFG_AC3ENABLE_MASK 0x000000e0 /* AC3 async input control - Not implemented */
#define HCFG_AC3ENABLE_ZVIDEO 0x00000080 /* Channels 0 and 1 replace ZVIDEO */
#define HCFG_AC3ENABLE_CDSPDIF 0x00000040 /* Channels 0 and 1 replace CDSPDIF */
#define HCFG_AC3ENABLE_GPSPDIF 0x00000020 /* Channels 0 and 1 replace GPSPDIF */
#define HCFG_AUTOMUTE 0x00000010 /* When set, the async sample rate convertors */
/* will automatically mute their output when */
/* they are not rate-locked to the external */
/* async audio source */
#define HCFG_LOCKSOUNDCACHE 0x00000008 /* 1 = Cancel bustmaster accesses to soundcache */
/* NOTE: This should generally never be used. */
#define HCFG_LOCKTANKCACHE_MASK 0x00000004 /* 1 = Cancel bustmaster accesses to tankcache */
/* NOTE: This should generally never be used. */
#define HCFG_LOCKTANKCACHE 0x01020014
#define HCFG_MUTEBUTTONENABLE 0x00000002 /* 1 = Master mute button sets AUDIOENABLE = 0. */
/* NOTE: This is a 'cheap' way to implement a */
/* master mute function on the mute button, and */
/* in general should not be used unless a more */
/* sophisticated master mute function has not */
/* been written. */
#define HCFG_AUDIOENABLE 0x00000001 /* 0 = CODECs transmit zero-valued samples */
/* Should be set to 1 when the EMU10K1 is */
/* completely initialized. */
//For Audigy, MPU port move to 0x70-0x74 ptr register
#define MUDATA 0x18 /* MPU401 data register (8 bits) */
#define MUCMD 0x19 /* MPU401 command register (8 bits) */
#define MUCMD_RESET 0xff /* RESET command */
#define MUCMD_ENTERUARTMODE 0x3f /* Enter_UART_mode command */
/* NOTE: All other commands are ignored */
#define MUSTAT MUCMD /* MPU401 status register (8 bits) */
#define MUSTAT_IRDYN 0x80 /* 0 = MIDI data or command ACK */
#define MUSTAT_ORDYN 0x40 /* 0 = MUDATA can accept a command or data */
#define A_IOCFG 0x18 /* GPIO on Audigy card (16bits) */
#define A_GPINPUT_MASK 0xff00
#define A_GPOUTPUT_MASK 0x00ff
// Audigy output/GPIO stuff taken from the kX drivers
#define A_IOCFG_GPOUT0 0x0044 /* analog/digital */
#define A_IOCFG_DISABLE_ANALOG 0x0040 /* = 'enable' for Audigy2 (chiprev=4) */
#define A_IOCFG_ENABLE_DIGITAL 0x0004
#define A_IOCFG_ENABLE_DIGITAL_AUDIGY4 0x0080
#define A_IOCFG_UNKNOWN_20 0x0020
#define A_IOCFG_DISABLE_AC97_FRONT 0x0080 /* turn off ac97 front -> front (10k2.1) */
#define A_IOCFG_GPOUT1 0x0002 /* IR? drive's internal bypass (?) */
#define A_IOCFG_GPOUT2 0x0001 /* IR */
#define A_IOCFG_MULTIPURPOSE_JACK 0x2000 /* center+lfe+rear_center (a2/a2ex) */
/* + digital for generic 10k2 */
#define A_IOCFG_DIGITAL_JACK 0x1000 /* digital for a2 platinum */
#define A_IOCFG_FRONT_JACK 0x4000
#define A_IOCFG_REAR_JACK 0x8000
#define A_IOCFG_PHONES_JACK 0x0100 /* LiveDrive */
/* outputs:
* for audigy2 platinum: 0xa00
* for a2 platinum ex: 0x1c00
* for a1 platinum: 0x0
*/
#define TIMER 0x1a /* Timer terminal count register */
/* NOTE: After the rate is changed, a maximum */
/* of 1024 sample periods should be allowed */
/* before the new rate is guaranteed accurate. */
#define TIMER_RATE_MASK 0x000003ff /* Timer interrupt rate in sample periods */
/* 0 == 1024 periods, [1..4] are not useful */
#define TIMER_RATE 0x0a00001a
#define AC97DATA 0x1c /* AC97 register set data register (16 bit) */
#define AC97ADDRESS 0x1e /* AC97 register set address register (8 bit) */
#define AC97ADDRESS_READY 0x80 /* Read-only bit, reflects CODEC READY signal */
#define AC97ADDRESS_ADDRESS 0x7f /* Address of indexed AC97 register */
/* Available on the Audigy 2 and Audigy 4 only. This is the P16V chip. */
#define PTR2 0x20 /* Indexed register set pointer register */
#define DATA2 0x24 /* Indexed register set data register */
#define IPR2 0x28 /* P16V interrupt pending register */
#define IPR2_PLAYBACK_CH_0_LOOP 0x00001000 /* Playback Channel 0 loop */
#define IPR2_PLAYBACK_CH_0_HALF_LOOP 0x00000100 /* Playback Channel 0 half loop */
#define IPR2_CAPTURE_CH_0_LOOP 0x00100000 /* Capture Channel 0 loop */
#define IPR2_CAPTURE_CH_0_HALF_LOOP 0x00010000 /* Capture Channel 0 half loop */
/* 0x00000100 Playback. Only in once per period.
* 0x00110000 Capture. Int on half buffer.
*/
#define INTE2 0x2c /* P16V Interrupt enable register. */
#define INTE2_PLAYBACK_CH_0_LOOP 0x00001000 /* Playback Channel 0 loop */
#define INTE2_PLAYBACK_CH_0_HALF_LOOP 0x00000100 /* Playback Channel 0 half loop */
#define INTE2_PLAYBACK_CH_1_LOOP 0x00002000 /* Playback Channel 1 loop */
#define INTE2_PLAYBACK_CH_1_HALF_LOOP 0x00000200 /* Playback Channel 1 half loop */
#define INTE2_PLAYBACK_CH_2_LOOP 0x00004000 /* Playback Channel 2 loop */
#define INTE2_PLAYBACK_CH_2_HALF_LOOP 0x00000400 /* Playback Channel 2 half loop */
#define INTE2_PLAYBACK_CH_3_LOOP 0x00008000 /* Playback Channel 3 loop */
#define INTE2_PLAYBACK_CH_3_HALF_LOOP 0x00000800 /* Playback Channel 3 half loop */
#define INTE2_CAPTURE_CH_0_LOOP 0x00100000 /* Capture Channel 0 loop */
#define INTE2_CAPTURE_CH_0_HALF_LOOP 0x00010000 /* Caputre Channel 0 half loop */
#define HCFG2 0x34 /* Defaults: 0, win2000 sets it to 00004201 */
/* 0x00000000 2-channel output. */
/* 0x00000200 8-channel output. */
/* 0x00000004 pauses stream/irq fail. */
/* Rest of bits no nothing to sound output */
/* bit 0: Enable P16V audio.
* bit 1: Lock P16V record memory cache.
* bit 2: Lock P16V playback memory cache.
* bit 3: Dummy record insert zero samples.
* bit 8: Record 8-channel in phase.
* bit 9: Playback 8-channel in phase.
* bit 11-12: Playback mixer attenuation: 0=0dB, 1=-6dB, 2=-12dB, 3=Mute.
* bit 13: Playback mixer enable.
* bit 14: Route SRC48 mixer output to fx engine.
* bit 15: Enable IEEE 1394 chip.
*/
#define IPR3 0x38 /* Cdif interrupt pending register */
#define INTE3 0x3c /* Cdif interrupt enable register. */
/************************************************************************************************/
/* PCI function 1 registers, address = <val> + PCIBASE1 */
/************************************************************************************************/
#define JOYSTICK1 0x00 /* Analog joystick port register */
#define JOYSTICK2 0x01 /* Analog joystick port register */
#define JOYSTICK3 0x02 /* Analog joystick port register */
#define JOYSTICK4 0x03 /* Analog joystick port register */
#define JOYSTICK5 0x04 /* Analog joystick port register */
#define JOYSTICK6 0x05 /* Analog joystick port register */
#define JOYSTICK7 0x06 /* Analog joystick port register */
#define JOYSTICK8 0x07 /* Analog joystick port register */
/* When writing, any write causes JOYSTICK_COMPARATOR output enable to be pulsed on write. */
/* When reading, use these bitfields: */
#define JOYSTICK_BUTTONS 0x0f /* Joystick button data */
#define JOYSTICK_COMPARATOR 0xf0 /* Joystick comparator data */
/********************************************************************************************************/
/* Emu10k1 pointer-offset register set, accessed through the PTR and DATA registers */
/********************************************************************************************************/
#define CPF 0x00 /* Current pitch and fraction register */
#define CPF_CURRENTPITCH_MASK 0xffff0000 /* Current pitch (linear, 0x4000 == unity pitch shift) */
#define CPF_CURRENTPITCH 0x10100000
#define CPF_STEREO_MASK 0x00008000 /* 1 = Even channel interleave, odd channel locked */
#define CPF_STOP_MASK 0x00004000 /* 1 = Current pitch forced to 0 */
#define CPF_FRACADDRESS_MASK 0x00003fff /* Linear fractional address of the current channel */
#define PTRX 0x01 /* Pitch target and send A/B amounts register */
#define PTRX_PITCHTARGET_MASK 0xffff0000 /* Pitch target of specified channel */
#define PTRX_PITCHTARGET 0x10100001
#define PTRX_FXSENDAMOUNT_A_MASK 0x0000ff00 /* Linear level of channel output sent to FX send bus A */
#define PTRX_FXSENDAMOUNT_A 0x08080001
#define PTRX_FXSENDAMOUNT_B_MASK 0x000000ff /* Linear level of channel output sent to FX send bus B */
#define PTRX_FXSENDAMOUNT_B 0x08000001
#define CVCF 0x02 /* Current volume and filter cutoff register */
#define CVCF_CURRENTVOL_MASK 0xffff0000 /* Current linear volume of specified channel */
#define CVCF_CURRENTVOL 0x10100002
#define CVCF_CURRENTFILTER_MASK 0x0000ffff /* Current filter cutoff frequency of specified channel */
#define CVCF_CURRENTFILTER 0x10000002
#define VTFT 0x03 /* Volume target and filter cutoff target register */
#define VTFT_VOLUMETARGET_MASK 0xffff0000 /* Volume target of specified channel */
#define VTFT_VOLUMETARGET 0x10100003
#define VTFT_FILTERTARGET_MASK 0x0000ffff /* Filter cutoff target of specified channel */
#define VTFT_FILTERTARGET 0x10000003
#define Z1 0x05 /* Filter delay memory 1 register */
#define Z2 0x04 /* Filter delay memory 2 register */
#define PSST 0x06 /* Send C amount and loop start address register */
#define PSST_FXSENDAMOUNT_C_MASK 0xff000000 /* Linear level of channel output sent to FX send bus C */
#define PSST_FXSENDAMOUNT_C 0x08180006
#define PSST_LOOPSTARTADDR_MASK 0x00ffffff /* Loop start address of the specified channel */
#define PSST_LOOPSTARTADDR 0x18000006
#define DSL 0x07 /* Send D amount and loop start address register */
#define DSL_FXSENDAMOUNT_D_MASK 0xff000000 /* Linear level of channel output sent to FX send bus D */
#define DSL_FXSENDAMOUNT_D 0x08180007
#define DSL_LOOPENDADDR_MASK 0x00ffffff /* Loop end address of the specified channel */
#define DSL_LOOPENDADDR 0x18000007
#define CCCA 0x08 /* Filter Q, interp. ROM, byte size, cur. addr register */
#define CCCA_RESONANCE 0xf0000000 /* Lowpass filter resonance (Q) height */
#define CCCA_INTERPROMMASK 0x0e000000 /* Selects passband of interpolation ROM */
/* 1 == full band, 7 == lowpass */
/* ROM 0 is used when pitch shifting downward or less */
/* then 3 semitones upward. Increasingly higher ROM */
/* numbers are used, typically in steps of 3 semitones, */
/* as upward pitch shifting is performed. */
#define CCCA_INTERPROM_0 0x00000000 /* Select interpolation ROM 0 */
#define CCCA_INTERPROM_1 0x02000000 /* Select interpolation ROM 1 */
#define CCCA_INTERPROM_2 0x04000000 /* Select interpolation ROM 2 */
#define CCCA_INTERPROM_3 0x06000000 /* Select interpolation ROM 3 */
#define CCCA_INTERPROM_4 0x08000000 /* Select interpolation ROM 4 */
#define CCCA_INTERPROM_5 0x0a000000 /* Select interpolation ROM 5 */
#define CCCA_INTERPROM_6 0x0c000000 /* Select interpolation ROM 6 */
#define CCCA_INTERPROM_7 0x0e000000 /* Select interpolation ROM 7 */
#define CCCA_8BITSELECT 0x01000000 /* 1 = Sound memory for this channel uses 8-bit samples */
#define CCCA_CURRADDR_MASK 0x00ffffff /* Current address of the selected channel */
#define CCCA_CURRADDR 0x18000008
#define CCR 0x09 /* Cache control register */
#define CCR_CACHEINVALIDSIZE 0x07190009
#define CCR_CACHEINVALIDSIZE_MASK 0xfe000000 /* Number of invalid samples cache for this channel */
#define CCR_CACHELOOPFLAG 0x01000000 /* 1 = Cache has a loop service pending */
#define CCR_INTERLEAVEDSAMPLES 0x00800000 /* 1 = A cache service will fetch interleaved samples */
#define CCR_WORDSIZEDSAMPLES 0x00400000 /* 1 = A cache service will fetch word sized samples */
#define CCR_READADDRESS 0x06100009
#define CCR_READADDRESS_MASK 0x003f0000 /* Location of cache just beyond current cache service */
#define CCR_LOOPINVALSIZE 0x0000fe00 /* Number of invalid samples in cache prior to loop */
/* NOTE: This is valid only if CACHELOOPFLAG is set */
#define CCR_LOOPFLAG 0x00000100 /* Set for a single sample period when a loop occurs */
#define CCR_CACHELOOPADDRHI 0x000000ff /* DSL_LOOPSTARTADDR's hi byte if CACHELOOPFLAG is set */
#define CLP 0x0a /* Cache loop register (valid if CCR_CACHELOOPFLAG = 1) */
/* NOTE: This register is normally not used */
#define CLP_CACHELOOPADDR 0x0000ffff /* Cache loop address (DSL_LOOPSTARTADDR [0..15]) */
#define FXRT 0x0b /* Effects send routing register */
/* NOTE: It is illegal to assign the same routing to */
/* two effects sends. */
#define FXRT_CHANNELA 0x000f0000 /* Effects send bus number for channel's effects send A */
#define FXRT_CHANNELB 0x00f00000 /* Effects send bus number for channel's effects send B */
#define FXRT_CHANNELC 0x0f000000 /* Effects send bus number for channel's effects send C */
#define FXRT_CHANNELD 0xf0000000 /* Effects send bus number for channel's effects send D */
#define A_HR 0x0b /* High Resolution. 24bit playback from host to DSP. */
#define MAPA 0x0c /* Cache map A */
#define MAPB 0x0d /* Cache map B */
#define MAP_PTE_MASK0 0xfffff000 /* The 20 MSBs of the PTE indexed by the PTI */
#define MAP_PTI_MASK0 0x00000fff /* The 12 bit index to one of the 4096 PTE dwords */
#define MAP_PTE_MASK1 0xffffe000 /* The 19 MSBs of the PTE indexed by the PTI */
#define MAP_PTI_MASK1 0x00001fff /* The 13 bit index to one of the 8192 PTE dwords */
/* 0x0e, 0x0f: Not used */
#define ENVVOL 0x10 /* Volume envelope register */
#define ENVVOL_MASK 0x0000ffff /* Current value of volume envelope state variable */
/* 0x8000-n == 666*n usec delay */
#define ATKHLDV 0x11 /* Volume envelope hold and attack register */
#define ATKHLDV_PHASE0 0x00008000 /* 0 = Begin attack phase */
#define ATKHLDV_HOLDTIME_MASK 0x00007f00 /* Envelope hold time (127-n == n*88.2msec) */
#define ATKHLDV_ATTACKTIME_MASK 0x0000007f /* Envelope attack time, log encoded */
/* 0 = infinite, 1 = 10.9msec, ... 0x7f = 5.5msec */
#define DCYSUSV 0x12 /* Volume envelope sustain and decay register */
#define DCYSUSV_PHASE1_MASK 0x00008000 /* 0 = Begin attack phase, 1 = begin release phase */
#define DCYSUSV_SUSTAINLEVEL_MASK 0x00007f00 /* 127 = full, 0 = off, 0.75dB increments */
#define DCYSUSV_CHANNELENABLE_MASK 0x00000080 /* 1 = Inhibit envelope engine from writing values in */
/* this channel and from writing to pitch, filter and */
/* volume targets. */
#define DCYSUSV_DECAYTIME_MASK 0x0000007f /* Volume envelope decay time, log encoded */
/* 0 = 43.7msec, 1 = 21.8msec, 0x7f = 22msec */
#define LFOVAL1 0x13 /* Modulation LFO value */
#define LFOVAL_MASK 0x0000ffff /* Current value of modulation LFO state variable */
/* 0x8000-n == 666*n usec delay */
#define ENVVAL 0x14 /* Modulation envelope register */
#define ENVVAL_MASK 0x0000ffff /* Current value of modulation envelope state variable */
/* 0x8000-n == 666*n usec delay */
#define ATKHLDM 0x15 /* Modulation envelope hold and attack register */
#define ATKHLDM_PHASE0 0x00008000 /* 0 = Begin attack phase */
#define ATKHLDM_HOLDTIME 0x00007f00 /* Envelope hold time (127-n == n*42msec) */
#define ATKHLDM_ATTACKTIME 0x0000007f /* Envelope attack time, log encoded */
/* 0 = infinite, 1 = 11msec, ... 0x7f = 5.5msec */
#define DCYSUSM 0x16 /* Modulation envelope decay and sustain register */
#define DCYSUSM_PHASE1_MASK 0x00008000 /* 0 = Begin attack phase, 1 = begin release phase */
#define DCYSUSM_SUSTAINLEVEL_MASK 0x00007f00 /* 127 = full, 0 = off, 0.75dB increments */
#define DCYSUSM_DECAYTIME_MASK 0x0000007f /* Envelope decay time, log encoded */
/* 0 = 43.7msec, 1 = 21.8msec, 0x7f = 22msec */
#define LFOVAL2 0x17 /* Vibrato LFO register */
#define LFOVAL2_MASK 0x0000ffff /* Current value of vibrato LFO state variable */
/* 0x8000-n == 666*n usec delay */
#define IP 0x18 /* Initial pitch register */
#define IP_MASK 0x0000ffff /* Exponential initial pitch shift */
/* 4 bits of octave, 12 bits of fractional octave */
#define IP_UNITY 0x0000e000 /* Unity pitch shift */
#define IFATN 0x19 /* Initial filter cutoff and attenuation register */
#define IFATN_FILTERCUTOFF_MASK 0x0000ff00 /* Initial filter cutoff frequency in exponential units */
/* 6 most significant bits are semitones */
/* 2 least significant bits are fractions */
#define IFATN_FILTERCUTOFF 0x08080019
#define IFATN_ATTENUATION_MASK 0x000000ff /* Initial attenuation in 0.375dB steps */
#define IFATN_ATTENUATION 0x08000019
#define PEFE 0x1a /* Pitch envelope and filter envelope amount register */
#define PEFE_PITCHAMOUNT_MASK 0x0000ff00 /* Pitch envlope amount */
/* Signed 2's complement, +/- one octave peak extremes */
#define PEFE_PITCHAMOUNT 0x0808001a
#define PEFE_FILTERAMOUNT_MASK 0x000000ff /* Filter envlope amount */
/* Signed 2's complement, +/- six octaves peak extremes */
#define PEFE_FILTERAMOUNT 0x0800001a
#define FMMOD 0x1b /* Vibrato/filter modulation from LFO register */
#define FMMOD_MODVIBRATO 0x0000ff00 /* Vibrato LFO modulation depth */
/* Signed 2's complement, +/- one octave extremes */
#define FMMOD_MOFILTER 0x000000ff /* Filter LFO modulation depth */
/* Signed 2's complement, +/- three octave extremes */
#define TREMFRQ 0x1c /* Tremolo amount and modulation LFO frequency register */
#define TREMFRQ_DEPTH 0x0000ff00 /* Tremolo depth */
/* Signed 2's complement, with +/- 12dB extremes */
#define TREMFRQ_FREQUENCY 0x000000ff /* Tremolo LFO frequency */
/* ??Hz steps, maximum of ?? Hz. */
#define FM2FRQ2 0x1d /* Vibrato amount and vibrato LFO frequency register */
#define FM2FRQ2_DEPTH 0x0000ff00 /* Vibrato LFO vibrato depth */
/* Signed 2's complement, +/- one octave extremes */
#define FM2FRQ2_FREQUENCY 0x000000ff /* Vibrato LFO frequency */
/* 0.039Hz steps, maximum of 9.85 Hz. */
#define TEMPENV 0x1e /* Tempory envelope register */
#define TEMPENV_MASK 0x0000ffff /* 16-bit value */
/* NOTE: All channels contain internal variables; do */
/* not write to these locations. */
/* 0x1f: not used */
#define CD0 0x20 /* Cache data 0 register */
#define CD1 0x21 /* Cache data 1 register */
#define CD2 0x22 /* Cache data 2 register */
#define CD3 0x23 /* Cache data 3 register */
#define CD4 0x24 /* Cache data 4 register */
#define CD5 0x25 /* Cache data 5 register */
#define CD6 0x26 /* Cache data 6 register */
#define CD7 0x27 /* Cache data 7 register */
#define CD8 0x28 /* Cache data 8 register */
#define CD9 0x29 /* Cache data 9 register */
#define CDA 0x2a /* Cache data A register */
#define CDB 0x2b /* Cache data B register */
#define CDC 0x2c /* Cache data C register */
#define CDD 0x2d /* Cache data D register */
#define CDE 0x2e /* Cache data E register */
#define CDF 0x2f /* Cache data F register */
/* 0x30-3f seem to be the same as 0x20-2f */
#define PTB 0x40 /* Page table base register */
#define PTB_MASK 0xfffff000 /* Physical address of the page table in host memory */
#define TCB 0x41 /* Tank cache base register */
#define TCB_MASK 0xfffff000 /* Physical address of the bottom of host based TRAM */
#define ADCCR 0x42 /* ADC sample rate/stereo control register */
#define ADCCR_RCHANENABLE 0x00000010 /* Enables right channel for writing to the host */
#define ADCCR_LCHANENABLE 0x00000008 /* Enables left channel for writing to the host */
/* NOTE: To guarantee phase coherency, both channels */
/* must be disabled prior to enabling both channels. */
#define A_ADCCR_RCHANENABLE 0x00000020
#define A_ADCCR_LCHANENABLE 0x00000010
#define A_ADCCR_SAMPLERATE_MASK 0x0000000F /* Audigy sample rate convertor output rate */
#define ADCCR_SAMPLERATE_MASK 0x00000007 /* Sample rate convertor output rate */
#define ADCCR_SAMPLERATE_48 0x00000000 /* 48kHz sample rate */
#define ADCCR_SAMPLERATE_44 0x00000001 /* 44.1kHz sample rate */
#define ADCCR_SAMPLERATE_32 0x00000002 /* 32kHz sample rate */
#define ADCCR_SAMPLERATE_24 0x00000003 /* 24kHz sample rate */
#define ADCCR_SAMPLERATE_22 0x00000004 /* 22.05kHz sample rate */
#define ADCCR_SAMPLERATE_16 0x00000005 /* 16kHz sample rate */
#define ADCCR_SAMPLERATE_11 0x00000006 /* 11.025kHz sample rate */
#define ADCCR_SAMPLERATE_8 0x00000007 /* 8kHz sample rate */
#define A_ADCCR_SAMPLERATE_12 0x00000006 /* 12kHz sample rate */
#define A_ADCCR_SAMPLERATE_11 0x00000007 /* 11.025kHz sample rate */
#define A_ADCCR_SAMPLERATE_8 0x00000008 /* 8kHz sample rate */
#define FXWC 0x43 /* FX output write channels register */
/* When set, each bit enables the writing of the */
/* corresponding FX output channel (internal registers */
/* 0x20-0x3f) to host memory. This mode of recording */
/* is 16bit, 48KHz only. All 32 channels can be enabled */
/* simultaneously. */
#define FXWC_DEFAULTROUTE_C (1<<0) /* left emu out? */
#define FXWC_DEFAULTROUTE_B (1<<1) /* right emu out? */
#define FXWC_DEFAULTROUTE_A (1<<12)
#define FXWC_DEFAULTROUTE_D (1<<13)
#define FXWC_ADCLEFT (1<<18)
#define FXWC_CDROMSPDIFLEFT (1<<18)
#define FXWC_ADCRIGHT (1<<19)
#define FXWC_CDROMSPDIFRIGHT (1<<19)
#define FXWC_MIC (1<<20)
#define FXWC_ZOOMLEFT (1<<20)
#define FXWC_ZOOMRIGHT (1<<21)
#define FXWC_SPDIFLEFT (1<<22) /* 0x00400000 */
#define FXWC_SPDIFRIGHT (1<<23) /* 0x00800000 */
#define A_TBLSZ 0x43 /* Effects Tank Internal Table Size. Only low byte or register used */
#define TCBS 0x44 /* Tank cache buffer size register */
#define TCBS_MASK 0x00000007 /* Tank cache buffer size field */
#define TCBS_BUFFSIZE_16K 0x00000000
#define TCBS_BUFFSIZE_32K 0x00000001
#define TCBS_BUFFSIZE_64K 0x00000002
#define TCBS_BUFFSIZE_128K 0x00000003
#define TCBS_BUFFSIZE_256K 0x00000004
#define TCBS_BUFFSIZE_512K 0x00000005
#define TCBS_BUFFSIZE_1024K 0x00000006
#define TCBS_BUFFSIZE_2048K 0x00000007
#define MICBA 0x45 /* AC97 microphone buffer address register */
#define MICBA_MASK 0xfffff000 /* 20 bit base address */
#define ADCBA 0x46 /* ADC buffer address register */
#define ADCBA_MASK 0xfffff000 /* 20 bit base address */
#define FXBA 0x47 /* FX Buffer Address */
#define FXBA_MASK 0xfffff000 /* 20 bit base address */
#define A_HWM 0x48 /* High PCI Water Mark - word access, defaults to 3f */
#define MICBS 0x49 /* Microphone buffer size register */
#define ADCBS 0x4a /* ADC buffer size register */
#define FXBS 0x4b /* FX buffer size register */
/* register: 0x4c..4f: ffff-ffff current amounts, per-channel */
/* The following mask values define the size of the ADC, MIX and FX buffers in bytes */
#define ADCBS_BUFSIZE_NONE 0x00000000
#define ADCBS_BUFSIZE_384 0x00000001
#define ADCBS_BUFSIZE_448 0x00000002
#define ADCBS_BUFSIZE_512 0x00000003
#define ADCBS_BUFSIZE_640 0x00000004
#define ADCBS_BUFSIZE_768 0x00000005
#define ADCBS_BUFSIZE_896 0x00000006
#define ADCBS_BUFSIZE_1024 0x00000007
#define ADCBS_BUFSIZE_1280 0x00000008
#define ADCBS_BUFSIZE_1536 0x00000009
#define ADCBS_BUFSIZE_1792 0x0000000a
#define ADCBS_BUFSIZE_2048 0x0000000b
#define ADCBS_BUFSIZE_2560 0x0000000c
#define ADCBS_BUFSIZE_3072 0x0000000d
#define ADCBS_BUFSIZE_3584 0x0000000e
#define ADCBS_BUFSIZE_4096 0x0000000f
#define ADCBS_BUFSIZE_5120 0x00000010
#define ADCBS_BUFSIZE_6144 0x00000011
#define ADCBS_BUFSIZE_7168 0x00000012
#define ADCBS_BUFSIZE_8192 0x00000013
#define ADCBS_BUFSIZE_10240 0x00000014
#define ADCBS_BUFSIZE_12288 0x00000015
#define ADCBS_BUFSIZE_14366 0x00000016
#define ADCBS_BUFSIZE_16384 0x00000017
#define ADCBS_BUFSIZE_20480 0x00000018
#define ADCBS_BUFSIZE_24576 0x00000019
#define ADCBS_BUFSIZE_28672 0x0000001a
#define ADCBS_BUFSIZE_32768 0x0000001b
#define ADCBS_BUFSIZE_40960 0x0000001c
#define ADCBS_BUFSIZE_49152 0x0000001d
#define ADCBS_BUFSIZE_57344 0x0000001e
#define ADCBS_BUFSIZE_65536 0x0000001f
/* Current Send B, A Amounts */
#define A_CSBA 0x4c
/* Current Send D, C Amounts */
#define A_CSDC 0x4d
/* Current Send F, E Amounts */
#define A_CSFE 0x4e
/* Current Send H, G Amounts */
#define A_CSHG 0x4f
#define CDCS 0x50 /* CD-ROM digital channel status register */
#define GPSCS 0x51 /* General Purpose SPDIF channel status register*/
#define DBG 0x52 /* DO NOT PROGRAM THIS REGISTER!!! MAY DESTROY CHIP */
/* S/PDIF Input C Channel Status */
#define A_SPSC 0x52
#define REG53 0x53 /* DO NOT PROGRAM THIS REGISTER!!! MAY DESTROY CHIP */
#define A_DBG 0x53
#define A_DBG_SINGLE_STEP 0x00020000 /* Set to zero to start dsp */
#define A_DBG_ZC 0x40000000 /* zero tram counter */
#define A_DBG_STEP_ADDR 0x000003ff
#define A_DBG_SATURATION_OCCURED 0x20000000
#define A_DBG_SATURATION_ADDR 0x0ffc0000
// NOTE: 0x54,55,56: 64-bit
#define SPCS0 0x54 /* SPDIF output Channel Status 0 register */
#define SPCS1 0x55 /* SPDIF output Channel Status 1 register */
#define SPCS2 0x56 /* SPDIF output Channel Status 2 register */
#define SPCS_CLKACCYMASK 0x30000000 /* Clock accuracy */
#define SPCS_CLKACCY_1000PPM 0x00000000 /* 1000 parts per million */
#define SPCS_CLKACCY_50PPM 0x10000000 /* 50 parts per million */
#define SPCS_CLKACCY_VARIABLE 0x20000000 /* Variable accuracy */
#define SPCS_SAMPLERATEMASK 0x0f000000 /* Sample rate */
#define SPCS_SAMPLERATE_44 0x00000000 /* 44.1kHz sample rate */
#define SPCS_SAMPLERATE_48 0x02000000 /* 48kHz sample rate */
#define SPCS_SAMPLERATE_32 0x03000000 /* 32kHz sample rate */
#define SPCS_CHANNELNUMMASK 0x00f00000 /* Channel number */
#define SPCS_CHANNELNUM_UNSPEC 0x00000000 /* Unspecified channel number */
#define SPCS_CHANNELNUM_LEFT 0x00100000 /* Left channel */
#define SPCS_CHANNELNUM_RIGHT 0x00200000 /* Right channel */
#define SPCS_SOURCENUMMASK 0x000f0000 /* Source number */
#define SPCS_SOURCENUM_UNSPEC 0x00000000 /* Unspecified source number */
#define SPCS_GENERATIONSTATUS 0x00008000 /* Originality flag (see IEC-958 spec) */
#define SPCS_CATEGORYCODEMASK 0x00007f00 /* Category code (see IEC-958 spec) */
#define SPCS_MODEMASK 0x000000c0 /* Mode (see IEC-958 spec) */
#define SPCS_EMPHASISMASK 0x00000038 /* Emphasis */
#define SPCS_EMPHASIS_NONE 0x00000000 /* No emphasis */
#define SPCS_EMPHASIS_50_15 0x00000008 /* 50/15 usec 2 channel */
#define SPCS_COPYRIGHT 0x00000004 /* Copyright asserted flag -- do not modify */
#define SPCS_NOTAUDIODATA 0x00000002 /* 0 = Digital audio, 1 = not audio */
#define SPCS_PROFESSIONAL 0x00000001 /* 0 = Consumer (IEC-958), 1 = pro (AES3-1992) */
/* 0x57: Not used */
/* The 32-bit CLIx and SOLx registers all have one bit per channel control/status */
#define CLIEL 0x58 /* Channel loop interrupt enable low register */
#define CLIEH 0x59 /* Channel loop interrupt enable high register */
#define CLIPL 0x5a /* Channel loop interrupt pending low register */
#define CLIPH 0x5b /* Channel loop interrupt pending high register */
#define SOLEL 0x5c /* Stop on loop enable low register */
#define SOLEH 0x5d /* Stop on loop enable high register */
#define SPBYPASS 0x5e /* SPDIF BYPASS mode register */
#define SPBYPASS_SPDIF0_MASK 0x00000003 /* SPDIF 0 bypass mode */
#define SPBYPASS_SPDIF1_MASK 0x0000000c /* SPDIF 1 bypass mode */
/* bypass mode: 0 - DSP; 1 - SPDIF A, 2 - SPDIF B, 3 - SPDIF C */
#define SPBYPASS_FORMAT 0x00000f00 /* If 1, SPDIF XX uses 24 bit, if 0 - 20 bit */
#define AC97SLOT 0x5f /* additional AC97 slots enable bits */
#define AC97SLOT_REAR_RIGHT 0x01 /* Rear left */
#define AC97SLOT_REAR_LEFT 0x02 /* Rear right */
#define AC97SLOT_CNTR 0x10 /* Center enable */
#define AC97SLOT_LFE 0x20 /* LFE enable */
/* PCB Revision */
#define A_PCB 0x5f
// NOTE: 0x60,61,62: 64-bit
#define CDSRCS 0x60 /* CD-ROM Sample Rate Converter status register */
#define GPSRCS 0x61 /* General Purpose SPDIF sample rate cvt status */
#define ZVSRCS 0x62 /* ZVideo sample rate converter status */
/* NOTE: This one has no SPDIFLOCKED field */
/* Assumes sample lock */
/* These three bitfields apply to CDSRCS, GPSRCS, and (except as noted) ZVSRCS. */
#define SRCS_SPDIFVALID 0x04000000 /* SPDIF stream valid */
#define SRCS_SPDIFLOCKED 0x02000000 /* SPDIF stream locked */
#define SRCS_RATELOCKED 0x01000000 /* Sample rate locked */
#define SRCS_ESTSAMPLERATE 0x0007ffff /* Do not modify this field. */
/* Note that these values can vary +/- by a small amount */
#define SRCS_SPDIFRATE_44 0x0003acd9
#define SRCS_SPDIFRATE_48 0x00040000
#define SRCS_SPDIFRATE_96 0x00080000
#define MICIDX 0x63 /* Microphone recording buffer index register */
#define MICIDX_MASK 0x0000ffff /* 16-bit value */
#define MICIDX_IDX 0x10000063
#define ADCIDX 0x64 /* ADC recording buffer index register */
#define ADCIDX_MASK 0x0000ffff /* 16 bit index field */
#define ADCIDX_IDX 0x10000064
#define A_ADCIDX 0x63
#define A_ADCIDX_IDX 0x10000063
#define A_MICIDX 0x64
#define A_MICIDX_IDX 0x10000064
#define FXIDX 0x65 /* FX recording buffer index register */
#define FXIDX_MASK 0x0000ffff /* 16-bit value */
#define FXIDX_IDX 0x10000065
/* The 32-bit HLIx and HLIPx registers all have one bit per channel control/status */
#define HLIEL 0x66 /* Channel half loop interrupt enable low register */
#define HLIEH 0x67 /* Channel half loop interrupt enable high register */
#define HLIPL 0x68 /* Channel half loop interrupt pending low register */
#define HLIPH 0x69 /* Channel half loop interrupt pending high register */
/* S/PDIF Host Record Index (bypasses SRC) */
#define A_SPRI 0x6a
/* S/PDIF Host Record Address */
#define A_SPRA 0x6b
/* S/PDIF Host Record Control */
#define A_SPRC 0x6c
/* Delayed Interrupt Counter & Enable */
#define A_DICE 0x6d
/* Tank Table Base */
#define A_TTB 0x6e
/* Tank Delay Offset */
#define A_TDOF 0x6f
/* This is the MPU port on the card (via the game port) */
#define A_MUDATA1 0x70
#define A_MUCMD1 0x71
#define A_MUSTAT1 A_MUCMD1
/* This is the MPU port on the Audigy Drive */
#define A_MUDATA2 0x72
#define A_MUCMD2 0x73
#define A_MUSTAT2 A_MUCMD2
/* The next two are the Audigy equivalent of FXWC */
/* the Audigy can record any output (16bit, 48kHz, up to 64 channel simultaneously) */
/* Each bit selects a channel for recording */
#define A_FXWC1 0x74 /* Selects 0x7f-0x60 for FX recording */
#define A_FXWC2 0x75 /* Selects 0x9f-0x80 for FX recording */
/* Extended Hardware Control */
#define A_SPDIF_SAMPLERATE 0x76 /* Set the sample rate of SPDIF output */
#define A_SAMPLE_RATE 0x76 /* Various sample rate settings. */
#define A_SAMPLE_RATE_NOT_USED 0x0ffc111e /* Bits that are not used and cannot be set. */
#define A_SAMPLE_RATE_UNKNOWN 0xf0030001 /* Bits that can be set, but have unknown use. */
#define A_SPDIF_RATE_MASK 0x000000e0 /* Any other values for rates, just use 48000 */
#define A_SPDIF_48000 0x00000000
#define A_SPDIF_192000 0x00000020
#define A_SPDIF_96000 0x00000040
#define A_SPDIF_44100 0x00000080
#define A_I2S_CAPTURE_RATE_MASK 0x00000e00 /* This sets the capture PCM rate, but it is */
#define A_I2S_CAPTURE_48000 0x00000000 /* unclear if this sets the ADC rate as well. */
#define A_I2S_CAPTURE_192000 0x00000200
#define A_I2S_CAPTURE_96000 0x00000400
#define A_I2S_CAPTURE_44100 0x00000800
#define A_PCM_RATE_MASK 0x0000e000 /* This sets the playback PCM rate on the P16V */
#define A_PCM_48000 0x00000000
#define A_PCM_192000 0x00002000
#define A_PCM_96000 0x00004000
#define A_PCM_44100 0x00008000
/* I2S0 Sample Rate Tracker Status */
#define A_SRT3 0x77
/* I2S1 Sample Rate Tracker Status */
#define A_SRT4 0x78
/* I2S2 Sample Rate Tracker Status */
#define A_SRT5 0x79
/* - default to 0x01080000 on my audigy 2 ZS --rlrevell */
/* Tank Table DMA Address */
#define A_TTDA 0x7a
/* Tank Table DMA Data */
#define A_TTDD 0x7b
#define A_FXRT2 0x7c
#define A_FXRT_CHANNELE 0x0000003f /* Effects send bus number for channel's effects send E */
#define A_FXRT_CHANNELF 0x00003f00 /* Effects send bus number for channel's effects send F */
#define A_FXRT_CHANNELG 0x003f0000 /* Effects send bus number for channel's effects send G */
#define A_FXRT_CHANNELH 0x3f000000 /* Effects send bus number for channel's effects send H */
#define A_SENDAMOUNTS 0x7d
#define A_FXSENDAMOUNT_E_MASK 0xFF000000
#define A_FXSENDAMOUNT_F_MASK 0x00FF0000
#define A_FXSENDAMOUNT_G_MASK 0x0000FF00
#define A_FXSENDAMOUNT_H_MASK 0x000000FF
/* 0x7c, 0x7e "high bit is used for filtering" */
/* The send amounts for this one are the same as used with the emu10k1 */
#define A_FXRT1 0x7e
#define A_FXRT_CHANNELA 0x0000003f
#define A_FXRT_CHANNELB 0x00003f00
#define A_FXRT_CHANNELC 0x003f0000
#define A_FXRT_CHANNELD 0x3f000000
/* 0x7f: Not used */
/* Each FX general purpose register is 32 bits in length, all bits are used */
#define FXGPREGBASE 0x100 /* FX general purpose registers base */
#define A_FXGPREGBASE 0x400 /* Audigy GPRs, 0x400 to 0x5ff */
#define A_TANKMEMCTLREGBASE 0x100 /* Tank memory control registers base - only for Audigy */
#define A_TANKMEMCTLREG_MASK 0x1f /* only 5 bits used - only for Audigy */
/* Tank audio data is logarithmically compressed down to 16 bits before writing to TRAM and is */
/* decompressed back to 20 bits on a read. There are a total of 160 locations, the last 32 */
/* locations are for external TRAM. */
#define TANKMEMDATAREGBASE 0x200 /* Tank memory data registers base */
#define TANKMEMDATAREG_MASK 0x000fffff /* 20 bit tank audio data field */
/* Combined address field and memory opcode or flag field. 160 locations, last 32 are external */
#define TANKMEMADDRREGBASE 0x300 /* Tank memory address registers base */
#define TANKMEMADDRREG_ADDR_MASK 0x000fffff /* 20 bit tank address field */
#define TANKMEMADDRREG_CLEAR 0x00800000 /* Clear tank memory */
#define TANKMEMADDRREG_ALIGN 0x00400000 /* Align read or write relative to tank access */
#define TANKMEMADDRREG_WRITE 0x00200000 /* Write to tank memory */
#define TANKMEMADDRREG_READ 0x00100000 /* Read from tank memory */
#define MICROCODEBASE 0x400 /* Microcode data base address */
/* Each DSP microcode instruction is mapped into 2 doublewords */
/* NOTE: When writing, always write the LO doubleword first. Reads can be in either order. */
#define LOWORD_OPX_MASK 0x000ffc00 /* Instruction operand X */
#define LOWORD_OPY_MASK 0x000003ff /* Instruction operand Y */
#define HIWORD_OPCODE_MASK 0x00f00000 /* Instruction opcode */
#define HIWORD_RESULT_MASK 0x000ffc00 /* Instruction result */
#define HIWORD_OPA_MASK 0x000003ff /* Instruction operand A */
/* Audigy Soundcard have a different instruction format */
#define A_MICROCODEBASE 0x600
#define A_LOWORD_OPY_MASK 0x000007ff
#define A_LOWORD_OPX_MASK 0x007ff000
#define A_HIWORD_OPCODE_MASK 0x0f000000
#define A_HIWORD_RESULT_MASK 0x007ff000
#define A_HIWORD_OPA_MASK 0x000007ff
/************************************************************************************************/
/* EMU1010m HANA FPGA registers */
/************************************************************************************************/
#define EMU_HANA_DESTHI 0x00 /* 0000xxx 3 bits Link Destination */
#define EMU_HANA_DESTLO 0x01 /* 00xxxxx 5 bits */
#define EMU_HANA_SRCHI 0x02 /* 0000xxx 3 bits Link Source */
#define EMU_HANA_SRCLO 0x03 /* 00xxxxx 5 bits */
#define EMU_HANA_DOCK_PWR 0x04 /* 000000x 1 bits Audio Dock power */
#define EMU_HANA_DOCK_PWR_ON 0x01 /* Audio Dock power on */
#define EMU_HANA_WCLOCK 0x05 /* 0000xxx 3 bits Word Clock source select */
/* Must be written after power on to reset DLL */
/* One is unable to detect the Audio dock without this */
#define EMU_HANA_WCLOCK_SRC_MASK 0x07
#define EMU_HANA_WCLOCK_INT_48K 0x00
#define EMU_HANA_WCLOCK_INT_44_1K 0x01
#define EMU_HANA_WCLOCK_HANA_SPDIF_IN 0x02
#define EMU_HANA_WCLOCK_HANA_ADAT_IN 0x03
#define EMU_HANA_WCLOCK_SYNC_BNCN 0x04
#define EMU_HANA_WCLOCK_2ND_HANA 0x05
#define EMU_HANA_WCLOCK_SRC_RESERVED 0x06
#define EMU_HANA_WCLOCK_OFF 0x07 /* For testing, forces fallback to DEFCLOCK */
#define EMU_HANA_WCLOCK_MULT_MASK 0x18
#define EMU_HANA_WCLOCK_1X 0x00
#define EMU_HANA_WCLOCK_2X 0x08
#define EMU_HANA_WCLOCK_4X 0x10
#define EMU_HANA_WCLOCK_MULT_RESERVED 0x18
#define EMU_HANA_DEFCLOCK 0x06 /* 000000x 1 bits Default Word Clock */
#define EMU_HANA_DEFCLOCK_48K 0x00
#define EMU_HANA_DEFCLOCK_44_1K 0x01
#define EMU_HANA_UNMUTE 0x07 /* 000000x 1 bits Mute all audio outputs */
#define EMU_MUTE 0x00
#define EMU_UNMUTE 0x01
#define EMU_HANA_FPGA_CONFIG 0x08 /* 00000xx 2 bits Config control of FPGAs */
#define EMU_HANA_FPGA_CONFIG_AUDIODOCK 0x01 /* Set in order to program FPGA on Audio Dock */
#define EMU_HANA_FPGA_CONFIG_HANA 0x02 /* Set in order to program FPGA on Hana */
#define EMU_HANA_IRQ_ENABLE 0x09 /* 000xxxx 4 bits IRQ Enable */
#define EMU_HANA_IRQ_WCLK_CHANGED 0x01
#define EMU_HANA_IRQ_ADAT 0x02
#define EMU_HANA_IRQ_DOCK 0x04
#define EMU_HANA_IRQ_DOCK_LOST 0x08
#define EMU_HANA_SPDIF_MODE 0x0a /* 00xxxxx 5 bits SPDIF MODE */
#define EMU_HANA_SPDIF_MODE_TX_COMSUMER 0x00
#define EMU_HANA_SPDIF_MODE_TX_PRO 0x01
#define EMU_HANA_SPDIF_MODE_TX_NOCOPY 0x02
#define EMU_HANA_SPDIF_MODE_RX_COMSUMER 0x00
#define EMU_HANA_SPDIF_MODE_RX_PRO 0x04
#define EMU_HANA_SPDIF_MODE_RX_NOCOPY 0x08
#define EMU_HANA_SPDIF_MODE_RX_INVALID 0x10
#define EMU_HANA_OPTICAL_TYPE 0x0b /* 00000xx 2 bits ADAT or SPDIF in/out */
#define EMU_HANA_OPTICAL_IN_SPDIF 0x00
#define EMU_HANA_OPTICAL_IN_ADAT 0x01
#define EMU_HANA_OPTICAL_OUT_SPDIF 0x00
#define EMU_HANA_OPTICAL_OUT_ADAT 0x02
#define EMU_HANA_MIDI_IN 0x0c /* 000000x 1 bit Control MIDI */
#define EMU_HANA_MIDI_IN_FROM_HAMOA 0x00 /* HAMOA MIDI in to Alice 2 MIDI B */
#define EMU_HANA_MIDI_IN_FROM_DOCK 0x01 /* Audio Dock MIDI in to Alice 2 MIDI B */
#define EMU_HANA_DOCK_LEDS_1 0x0d /* 000xxxx 4 bit Audio Dock LEDs */
#define EMU_HANA_DOCK_LEDS_1_MIDI1 0x01 /* MIDI 1 LED on */
#define EMU_HANA_DOCK_LEDS_1_MIDI2 0x02 /* MIDI 2 LED on */
#define EMU_HANA_DOCK_LEDS_1_SMPTE_IN 0x04 /* SMPTE IN LED on */
#define EMU_HANA_DOCK_LEDS_1_SMPTE_OUT 0x08 /* SMPTE OUT LED on */
#define EMU_HANA_DOCK_LEDS_2 0x0e /* 0xxxxxx 6 bit Audio Dock LEDs */
#define EMU_HANA_DOCK_LEDS_2_44K 0x01 /* 44.1 kHz LED on */
#define EMU_HANA_DOCK_LEDS_2_48K 0x02 /* 48 kHz LED on */
#define EMU_HANA_DOCK_LEDS_2_96K 0x04 /* 96 kHz LED on */
#define EMU_HANA_DOCK_LEDS_2_192K 0x08 /* 192 kHz LED on */
#define EMU_HANA_DOCK_LEDS_2_LOCK 0x10 /* LOCK LED on */
#define EMU_HANA_DOCK_LEDS_2_EXT 0x20 /* EXT LED on */
#define EMU_HANA_DOCK_LEDS_3 0x0f /* 0xxxxxx 6 bit Audio Dock LEDs */
#define EMU_HANA_DOCK_LEDS_3_CLIP_A 0x01 /* Mic A Clip LED on */
#define EMU_HANA_DOCK_LEDS_3_CLIP_B 0x02 /* Mic B Clip LED on */
#define EMU_HANA_DOCK_LEDS_3_SIGNAL_A 0x04 /* Signal A Clip LED on */
#define EMU_HANA_DOCK_LEDS_3_SIGNAL_B 0x08 /* Signal B Clip LED on */
#define EMU_HANA_DOCK_LEDS_3_MANUAL_CLIP 0x10 /* Manual Clip detection */
#define EMU_HANA_DOCK_LEDS_3_MANUAL_SIGNAL 0x20 /* Manual Signal detection */
#define EMU_HANA_ADC_PADS 0x10 /* 0000xxx 3 bit Audio Dock ADC 14dB pads */
#define EMU_HANA_DOCK_ADC_PAD1 0x01 /* 14dB Attenuation on Audio Dock ADC 1 */
#define EMU_HANA_DOCK_ADC_PAD2 0x02 /* 14dB Attenuation on Audio Dock ADC 2 */
#define EMU_HANA_DOCK_ADC_PAD3 0x04 /* 14dB Attenuation on Audio Dock ADC 3 */
#define EMU_HANA_0202_ADC_PAD1 0x08 /* 14dB Attenuation on 0202 ADC 1 */
#define EMU_HANA_DOCK_MISC 0x11 /* 0xxxxxx 6 bit Audio Dock misc bits */
#define EMU_HANA_DOCK_DAC1_MUTE 0x01 /* DAC 1 Mute */
#define EMU_HANA_DOCK_DAC2_MUTE 0x02 /* DAC 2 Mute */
#define EMU_HANA_DOCK_DAC3_MUTE 0x04 /* DAC 3 Mute */
#define EMU_HANA_DOCK_DAC4_MUTE 0x08 /* DAC 4 Mute */
#define EMU_HANA_DOCK_PHONES_192_DAC1 0x00 /* DAC 1 Headphones source at 192kHz */
#define EMU_HANA_DOCK_PHONES_192_DAC2 0x10 /* DAC 2 Headphones source at 192kHz */
#define EMU_HANA_DOCK_PHONES_192_DAC3 0x20 /* DAC 3 Headphones source at 192kHz */
#define EMU_HANA_DOCK_PHONES_192_DAC4 0x30 /* DAC 4 Headphones source at 192kHz */
#define EMU_HANA_MIDI_OUT 0x12 /* 00xxxxx 5 bit Source for each MIDI out port */
#define EMU_HANA_MIDI_OUT_0202 0x01 /* 0202 MIDI from Alice 2. 0 = A, 1 = B */
#define EMU_HANA_MIDI_OUT_DOCK1 0x02 /* Audio Dock MIDI1 front, from Alice 2. 0 = A, 1 = B */
#define EMU_HANA_MIDI_OUT_DOCK2 0x04 /* Audio Dock MIDI2 rear, from Alice 2. 0 = A, 1 = B */
#define EMU_HANA_MIDI_OUT_SYNC2 0x08 /* Sync card. Not the actual MIDI out jack. 0 = A, 1 = B */
#define EMU_HANA_MIDI_OUT_LOOP 0x10 /* 0 = bits (3:0) normal. 1 = MIDI loopback enabled. */
#define EMU_HANA_DAC_PADS 0x13 /* 00xxxxx 5 bit DAC 14dB attenuation pads */
#define EMU_HANA_DOCK_DAC_PAD1 0x01 /* 14dB Attenuation on AudioDock DAC 1. Left and Right */
#define EMU_HANA_DOCK_DAC_PAD2 0x02 /* 14dB Attenuation on AudioDock DAC 2. Left and Right */
#define EMU_HANA_DOCK_DAC_PAD3 0x04 /* 14dB Attenuation on AudioDock DAC 3. Left and Right */
#define EMU_HANA_DOCK_DAC_PAD4 0x08 /* 14dB Attenuation on AudioDock DAC 4. Left and Right */
#define EMU_HANA_0202_DAC_PAD1 0x10 /* 14dB Attenuation on 0202 DAC 1. Left and Right */
/* 0x14 - 0x1f Unused R/W registers */
#define EMU_HANA_IRQ_STATUS 0x20 /* 000xxxx 4 bits IRQ Status */
#if 0 /* Already defined for reg 0x09 IRQ_ENABLE */
#define EMU_HANA_IRQ_WCLK_CHANGED 0x01
#define EMU_HANA_IRQ_ADAT 0x02
#define EMU_HANA_IRQ_DOCK 0x04
#define EMU_HANA_IRQ_DOCK_LOST 0x08
#endif
#define EMU_HANA_OPTION_CARDS 0x21 /* 000xxxx 4 bits Presence of option cards */
#define EMU_HANA_OPTION_HAMOA 0x01 /* HAMOA card present */
#define EMU_HANA_OPTION_SYNC 0x02 /* Sync card present */
#define EMU_HANA_OPTION_DOCK_ONLINE 0x04 /* Audio Dock online and FPGA configured */
#define EMU_HANA_OPTION_DOCK_OFFLINE 0x08 /* Audio Dock online and FPGA not configured */
#define EMU_HANA_ID 0x22 /* 1010101 7 bits ID byte & 0x7f = 0x55 */
#define EMU_HANA_MAJOR_REV 0x23 /* 0000xxx 3 bit Hana FPGA Major rev */
#define EMU_HANA_MINOR_REV 0x24 /* 0000xxx 3 bit Hana FPGA Minor rev */
#define EMU_DOCK_MAJOR_REV 0x25 /* 0000xxx 3 bit Audio Dock FPGA Major rev */
#define EMU_DOCK_MINOR_REV 0x26 /* 0000xxx 3 bit Audio Dock FPGA Minor rev */
#define EMU_DOCK_BOARD_ID 0x27 /* 00000xx 2 bits Audio Dock ID pins */
#define EMU_DOCK_BOARD_ID0 0x00 /* ID bit 0 */
#define EMU_DOCK_BOARD_ID1 0x03 /* ID bit 1 */
#define EMU_HANA_WC_SPDIF_HI 0x28 /* 0xxxxxx 6 bit SPDIF IN Word clock, upper 6 bits */
#define EMU_HANA_WC_SPDIF_LO 0x29 /* 0xxxxxx 6 bit SPDIF IN Word clock, lower 6 bits */
#define EMU_HANA_WC_ADAT_HI 0x2a /* 0xxxxxx 6 bit ADAT IN Word clock, upper 6 bits */
#define EMU_HANA_WC_ADAT_LO 0x2b /* 0xxxxxx 6 bit ADAT IN Word clock, lower 6 bits */
#define EMU_HANA_WC_BNC_LO 0x2c /* 0xxxxxx 6 bit BNC IN Word clock, lower 6 bits */
#define EMU_HANA_WC_BNC_HI 0x2d /* 0xxxxxx 6 bit BNC IN Word clock, upper 6 bits */
#define EMU_HANA2_WC_SPDIF_HI 0x2e /* 0xxxxxx 6 bit HANA2 SPDIF IN Word clock, upper 6 bits */
#define EMU_HANA2_WC_SPDIF_LO 0x2f /* 0xxxxxx 6 bit HANA2 SPDIF IN Word clock, lower 6 bits */
/* 0x30 - 0x3f Unused Read only registers */
/************************************************************************************************/
/* EMU1010m HANA Destinations */
/************************************************************************************************/
/* Hana, original 1010,1212,1820 using Alice2
* Destiniations for SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00, 0x00-0x0f: 16 EMU32 channels to Alice2
* 0x01, 0x10-0x1f: 32 Elink channels to Audio Dock
* 0x01, 0x00: Dock DAC 1 Left
* 0x01, 0x04: Dock DAC 1 Right
* 0x01, 0x08: Dock DAC 2 Left
* 0x01, 0x0c: Dock DAC 2 Right
* 0x01, 0x10: Dock DAC 3 Left
* 0x01, 0x12: PHONES Left
* 0x01, 0x14: Dock DAC 3 Right
* 0x01, 0x16: PHONES Right
* 0x01, 0x18: Dock DAC 4 Left
* 0x01, 0x1a: S/PDIF Left
* 0x01, 0x1c: Dock DAC 4 Right
* 0x01, 0x1e: S/PDIF Right
* 0x02, 0x00: Hana S/PDIF Left
* 0x02, 0x01: Hana S/PDIF Right
* 0x03, 0x00: Hanoa DAC Left
* 0x03, 0x01: Hanoa DAC Right
* 0x04, 0x00-0x07: Hana ADAT
* 0x05, 0x00: I2S0 Left to Alice2
* 0x05, 0x01: I2S0 Right to Alice2
* 0x06, 0x00: I2S0 Left to Alice2
* 0x06, 0x01: I2S0 Right to Alice2
* 0x07, 0x00: I2S0 Left to Alice2
* 0x07, 0x01: I2S0 Right to Alice2
*
* Hana2 never released, but used Tina
* Not needed.
*
* Hana3, rev2 1010,1212,1616 using Tina
* Destinations for SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00, 0x00-0x0f: 16 EMU32A channels to Tina
* 0x01, 0x10-0x1f: 32 EDI channels to Micro Dock
* 0x01, 0x00: Dock DAC 1 Left
* 0x01, 0x04: Dock DAC 1 Right
* 0x01, 0x08: Dock DAC 2 Left
* 0x01, 0x0c: Dock DAC 2 Right
* 0x01, 0x10: Dock DAC 3 Left
* 0x01, 0x12: Dock S/PDIF Left
* 0x01, 0x14: Dock DAC 3 Right
* 0x01, 0x16: Dock S/PDIF Right
* 0x01, 0x18-0x1f: Dock ADAT 0-7
* 0x02, 0x00: Hana3 S/PDIF Left
* 0x02, 0x01: Hana3 S/PDIF Right
* 0x03, 0x00: Hanoa DAC Left
* 0x03, 0x01: Hanoa DAC Right
* 0x04, 0x00-0x07: Hana3 ADAT 0-7
* 0x05, 0x00-0x0f: 16 EMU32B channels to Tina
* 0x06-0x07: Not used
*
* HanaLite, rev1 0404 using Alice2
* Destiniations for SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00, 0x00-0x0f: 16 EMU32 channels to Alice2
* 0x01: Not used
* 0x02, 0x00: S/PDIF Left
* 0x02, 0x01: S/PDIF Right
* 0x03, 0x00: DAC Left
* 0x03, 0x01: DAC Right
* 0x04-0x07: Not used
*
* HanaLiteLite, rev2 0404 using Alice2
* Destiniations for SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00, 0x00-0x0f: 16 EMU32 channels to Alice2
* 0x01: Not used
* 0x02, 0x00: S/PDIF Left
* 0x02, 0x01: S/PDIF Right
* 0x03, 0x00: DAC Left
* 0x03, 0x01: DAC Right
* 0x04-0x07: Not used
*
* Mana, Cardbus 1616 using Tina2
* Destinations for SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00, 0x00-0x0f: 16 EMU32A channels to Tina2
* 0x01, 0x10-0x1f: 32 EDI channels to Micro Dock
* 0x01, 0x00: Dock DAC 1 Left
* 0x01, 0x04: Dock DAC 1 Right
* 0x01, 0x08: Dock DAC 2 Left
* 0x01, 0x0c: Dock DAC 2 Right
* 0x01, 0x10: Dock DAC 3 Left
* 0x01, 0x12: Dock S/PDIF Left
* 0x01, 0x14: Dock DAC 3 Right
* 0x01, 0x16: Dock S/PDIF Right
* 0x01, 0x18-0x1f: Dock ADAT 0-7
* 0x02: Not used
* 0x03, 0x00: Mana DAC Left
* 0x03, 0x01: Mana DAC Right
* 0x04, 0x00-0x0f: 16 EMU32B channels to Tina2
* 0x05-0x07: Not used
*
*
*/
/* 32-bit destinations of signal in the Hana FPGA. Destinations are either
* physical outputs of Hana, or outputs going to Alice2 (audigy) for capture
* - 16 x EMU_DST_ALICE2_EMU32_X.
*/
/* EMU32 = 32-bit serial channel between Alice2 (audigy) and Hana (FPGA) */
/* EMU_DST_ALICE2_EMU32_X - data channels from Hana to Alice2 used for capture.
* Which data is fed into a EMU_DST_ALICE2_EMU32_X channel in Hana depends on
* setup of mixer control for each destination - see emumixer.c -
* snd_emu1010_output_enum_ctls[], snd_emu1010_input_enum_ctls[]
*/
#define EMU_DST_ALICE2_EMU32_0 0x000f /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_1 0x0000 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_2 0x0001 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_3 0x0002 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_4 0x0003 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_5 0x0004 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_6 0x0005 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_7 0x0006 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_8 0x0007 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_9 0x0008 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_A 0x0009 /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_B 0x000a /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_C 0x000b /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_D 0x000c /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_E 0x000d /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_ALICE2_EMU32_F 0x000e /* 16 EMU32 channels to Alice2 +0 to +0xf */
#define EMU_DST_DOCK_DAC1_LEFT1 0x0100 /* Audio Dock DAC1 Left, 1st or 48kHz only */
#define EMU_DST_DOCK_DAC1_LEFT2 0x0101 /* Audio Dock DAC1 Left, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC1_LEFT3 0x0102 /* Audio Dock DAC1 Left, 3rd or 192kHz */
#define EMU_DST_DOCK_DAC1_LEFT4 0x0103 /* Audio Dock DAC1 Left, 4th or 192kHz */
#define EMU_DST_DOCK_DAC1_RIGHT1 0x0104 /* Audio Dock DAC1 Right, 1st or 48kHz only */
#define EMU_DST_DOCK_DAC1_RIGHT2 0x0105 /* Audio Dock DAC1 Right, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC1_RIGHT3 0x0106 /* Audio Dock DAC1 Right, 3rd or 192kHz */
#define EMU_DST_DOCK_DAC1_RIGHT4 0x0107 /* Audio Dock DAC1 Right, 4th or 192kHz */
#define EMU_DST_DOCK_DAC2_LEFT1 0x0108 /* Audio Dock DAC2 Left, 1st or 48kHz only */
#define EMU_DST_DOCK_DAC2_LEFT2 0x0109 /* Audio Dock DAC2 Left, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC2_LEFT3 0x010a /* Audio Dock DAC2 Left, 3rd or 192kHz */
#define EMU_DST_DOCK_DAC2_LEFT4 0x010b /* Audio Dock DAC2 Left, 4th or 192kHz */
#define EMU_DST_DOCK_DAC2_RIGHT1 0x010c /* Audio Dock DAC2 Right, 1st or 48kHz only */
#define EMU_DST_DOCK_DAC2_RIGHT2 0x010d /* Audio Dock DAC2 Right, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC2_RIGHT3 0x010e /* Audio Dock DAC2 Right, 3rd or 192kHz */
#define EMU_DST_DOCK_DAC2_RIGHT4 0x010f /* Audio Dock DAC2 Right, 4th or 192kHz */
#define EMU_DST_DOCK_DAC3_LEFT1 0x0110 /* Audio Dock DAC1 Left, 1st or 48kHz only */
#define EMU_DST_DOCK_DAC3_LEFT2 0x0111 /* Audio Dock DAC1 Left, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC3_LEFT3 0x0112 /* Audio Dock DAC1 Left, 3rd or 192kHz */
#define EMU_DST_DOCK_DAC3_LEFT4 0x0113 /* Audio Dock DAC1 Left, 4th or 192kHz */
#define EMU_DST_DOCK_PHONES_LEFT1 0x0112 /* Audio Dock PHONES Left, 1st or 48kHz only */
#define EMU_DST_DOCK_PHONES_LEFT2 0x0113 /* Audio Dock PHONES Left, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC3_RIGHT1 0x0114 /* Audio Dock DAC1 Right, 1st or 48kHz only */
#define EMU_DST_DOCK_DAC3_RIGHT2 0x0115 /* Audio Dock DAC1 Right, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC3_RIGHT3 0x0116 /* Audio Dock DAC1 Right, 3rd or 192kHz */
#define EMU_DST_DOCK_DAC3_RIGHT4 0x0117 /* Audio Dock DAC1 Right, 4th or 192kHz */
#define EMU_DST_DOCK_PHONES_RIGHT1 0x0116 /* Audio Dock PHONES Right, 1st or 48kHz only */
#define EMU_DST_DOCK_PHONES_RIGHT2 0x0117 /* Audio Dock PHONES Right, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC4_LEFT1 0x0118 /* Audio Dock DAC2 Left, 1st or 48kHz only */
#define EMU_DST_DOCK_DAC4_LEFT2 0x0119 /* Audio Dock DAC2 Left, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC4_LEFT3 0x011a /* Audio Dock DAC2 Left, 3rd or 192kHz */
#define EMU_DST_DOCK_DAC4_LEFT4 0x011b /* Audio Dock DAC2 Left, 4th or 192kHz */
#define EMU_DST_DOCK_SPDIF_LEFT1 0x011a /* Audio Dock SPDIF Left, 1st or 48kHz only */
#define EMU_DST_DOCK_SPDIF_LEFT2 0x011b /* Audio Dock SPDIF Left, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC4_RIGHT1 0x011c /* Audio Dock DAC2 Right, 1st or 48kHz only */
#define EMU_DST_DOCK_DAC4_RIGHT2 0x011d /* Audio Dock DAC2 Right, 2nd or 96kHz */
#define EMU_DST_DOCK_DAC4_RIGHT3 0x011e /* Audio Dock DAC2 Right, 3rd or 192kHz */
#define EMU_DST_DOCK_DAC4_RIGHT4 0x011f /* Audio Dock DAC2 Right, 4th or 192kHz */
#define EMU_DST_DOCK_SPDIF_RIGHT1 0x011e /* Audio Dock SPDIF Right, 1st or 48kHz only */
#define EMU_DST_DOCK_SPDIF_RIGHT2 0x011f /* Audio Dock SPDIF Right, 2nd or 96kHz */
#define EMU_DST_HANA_SPDIF_LEFT1 0x0200 /* Hana SPDIF Left, 1st or 48kHz only */
#define EMU_DST_HANA_SPDIF_LEFT2 0x0202 /* Hana SPDIF Left, 2nd or 96kHz */
#define EMU_DST_HANA_SPDIF_RIGHT1 0x0201 /* Hana SPDIF Right, 1st or 48kHz only */
#define EMU_DST_HANA_SPDIF_RIGHT2 0x0203 /* Hana SPDIF Right, 2nd or 96kHz */
#define EMU_DST_HAMOA_DAC_LEFT1 0x0300 /* Hamoa DAC Left, 1st or 48kHz only */
#define EMU_DST_HAMOA_DAC_LEFT2 0x0302 /* Hamoa DAC Left, 2nd or 96kHz */
#define EMU_DST_HAMOA_DAC_LEFT3 0x0304 /* Hamoa DAC Left, 3rd or 192kHz */
#define EMU_DST_HAMOA_DAC_LEFT4 0x0306 /* Hamoa DAC Left, 4th or 192kHz */
#define EMU_DST_HAMOA_DAC_RIGHT1 0x0301 /* Hamoa DAC Right, 1st or 48kHz only */
#define EMU_DST_HAMOA_DAC_RIGHT2 0x0303 /* Hamoa DAC Right, 2nd or 96kHz */
#define EMU_DST_HAMOA_DAC_RIGHT3 0x0305 /* Hamoa DAC Right, 3rd or 192kHz */
#define EMU_DST_HAMOA_DAC_RIGHT4 0x0307 /* Hamoa DAC Right, 4th or 192kHz */
#define EMU_DST_HANA_ADAT 0x0400 /* Hana ADAT 8 channel out +0 to +7 */
#define EMU_DST_ALICE_I2S0_LEFT 0x0500 /* Alice2 I2S0 Left */
#define EMU_DST_ALICE_I2S0_RIGHT 0x0501 /* Alice2 I2S0 Right */
#define EMU_DST_ALICE_I2S1_LEFT 0x0600 /* Alice2 I2S1 Left */
#define EMU_DST_ALICE_I2S1_RIGHT 0x0601 /* Alice2 I2S1 Right */
#define EMU_DST_ALICE_I2S2_LEFT 0x0700 /* Alice2 I2S2 Left */
#define EMU_DST_ALICE_I2S2_RIGHT 0x0701 /* Alice2 I2S2 Right */
/* Additional destinations for 1616(M)/Microdock */
/* Microdock S/PDIF OUT Left, 1st or 48kHz only */
#define EMU_DST_MDOCK_SPDIF_LEFT1 0x0112
/* Microdock S/PDIF OUT Left, 2nd or 96kHz */
#define EMU_DST_MDOCK_SPDIF_LEFT2 0x0113
/* Microdock S/PDIF OUT Right, 1st or 48kHz only */
#define EMU_DST_MDOCK_SPDIF_RIGHT1 0x0116
/* Microdock S/PDIF OUT Right, 2nd or 96kHz */
#define EMU_DST_MDOCK_SPDIF_RIGHT2 0x0117
/* Microdock S/PDIF ADAT 8 channel out +8 to +f */
#define EMU_DST_MDOCK_ADAT 0x0118
/* Headphone jack on 1010 cardbus? 44.1/48kHz only? */
#define EMU_DST_MANA_DAC_LEFT 0x0300
/* Headphone jack on 1010 cardbus? 44.1/48kHz only? */
#define EMU_DST_MANA_DAC_RIGHT 0x0301
/************************************************************************************************/
/* EMU1010m HANA Sources */
/************************************************************************************************/
/* Hana, original 1010,1212,1820 using Alice2
* Sources SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00,0x00-0x1f: Silence
* 0x01, 0x10-0x1f: 32 Elink channels from Audio Dock
* 0x01, 0x00: Dock Mic A
* 0x01, 0x04: Dock Mic B
* 0x01, 0x08: Dock ADC 1 Left
* 0x01, 0x0c: Dock ADC 1 Right
* 0x01, 0x10: Dock ADC 2 Left
* 0x01, 0x14: Dock ADC 2 Right
* 0x01, 0x18: Dock ADC 3 Left
* 0x01, 0x1c: Dock ADC 3 Right
* 0x02, 0x00: Hana ADC Left
* 0x02, 0x01: Hana ADC Right
* 0x03, 0x00-0x0f: 16 inputs from Alice2 Emu32A output
* 0x03, 0x10-0x1f: 16 inputs from Alice2 Emu32B output
* 0x04, 0x00-0x07: Hana ADAT
* 0x05, 0x00: Hana S/PDIF Left
* 0x05, 0x01: Hana S/PDIF Right
* 0x06-0x07: Not used
*
* Hana2 never released, but used Tina
* Not needed.
*
* Hana3, rev2 1010,1212,1616 using Tina
* Sources SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00,0x00-0x1f: Silence
* 0x01, 0x10-0x1f: 32 Elink channels from Audio Dock
* 0x01, 0x00: Dock Mic A
* 0x01, 0x04: Dock Mic B
* 0x01, 0x08: Dock ADC 1 Left
* 0x01, 0x0c: Dock ADC 1 Right
* 0x01, 0x10: Dock ADC 2 Left
* 0x01, 0x12: Dock S/PDIF Left
* 0x01, 0x14: Dock ADC 2 Right
* 0x01, 0x16: Dock S/PDIF Right
* 0x01, 0x18-0x1f: Dock ADAT 0-7
* 0x01, 0x18: Dock ADC 3 Left
* 0x01, 0x1c: Dock ADC 3 Right
* 0x02, 0x00: Hanoa ADC Left
* 0x02, 0x01: Hanoa ADC Right
* 0x03, 0x00-0x0f: 16 inputs from Tina Emu32A output
* 0x03, 0x10-0x1f: 16 inputs from Tina Emu32B output
* 0x04, 0x00-0x07: Hana3 ADAT
* 0x05, 0x00: Hana3 S/PDIF Left
* 0x05, 0x01: Hana3 S/PDIF Right
* 0x06-0x07: Not used
*
* HanaLite, rev1 0404 using Alice2
* Sources SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00,0x00-0x1f: Silence
* 0x01: Not used
* 0x02, 0x00: ADC Left
* 0x02, 0x01: ADC Right
* 0x03, 0x00-0x0f: 16 inputs from Alice2 Emu32A output
* 0x03, 0x10-0x1f: 16 inputs from Alice2 Emu32B output
* 0x04: Not used
* 0x05, 0x00: S/PDIF Left
* 0x05, 0x01: S/PDIF Right
* 0x06-0x07: Not used
*
* HanaLiteLite, rev2 0404 using Alice2
* Sources SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00,0x00-0x1f: Silence
* 0x01: Not used
* 0x02, 0x00: ADC Left
* 0x02, 0x01: ADC Right
* 0x03, 0x00-0x0f: 16 inputs from Alice2 Emu32A output
* 0x03, 0x10-0x1f: 16 inputs from Alice2 Emu32B output
* 0x04: Not used
* 0x05, 0x00: S/PDIF Left
* 0x05, 0x01: S/PDIF Right
* 0x06-0x07: Not used
*
* Mana, Cardbus 1616 using Tina2
* Sources SRATEX = 1X rates: 44.1 kHz or 48 kHz
* 0x00,0x00-0x1f: Silence
* 0x01, 0x10-0x1f: 32 Elink channels from Audio Dock
* 0x01, 0x00: Dock Mic A
* 0x01, 0x04: Dock Mic B
* 0x01, 0x08: Dock ADC 1 Left
* 0x01, 0x0c: Dock ADC 1 Right
* 0x01, 0x10: Dock ADC 2 Left
* 0x01, 0x12: Dock S/PDIF Left
* 0x01, 0x14: Dock ADC 2 Right
* 0x01, 0x16: Dock S/PDIF Right
* 0x01, 0x18-0x1f: Dock ADAT 0-7
* 0x01, 0x18: Dock ADC 3 Left
* 0x01, 0x1c: Dock ADC 3 Right
* 0x02: Not used
* 0x03, 0x00-0x0f: 16 inputs from Tina Emu32A output
* 0x03, 0x10-0x1f: 16 inputs from Tina Emu32B output
* 0x04-0x07: Not used
*
*/
/* 32-bit sources of signal in the Hana FPGA. The sources are routed to
* destinations using mixer control for each destination - see emumixer.c
* Sources are either physical inputs of FPGA,
* or outputs from Alice (audigy) - 16 x EMU_SRC_ALICE_EMU32A +
* 16 x EMU_SRC_ALICE_EMU32B
*/
#define EMU_SRC_SILENCE 0x0000 /* Silence */
#define EMU_SRC_DOCK_MIC_A1 0x0100 /* Audio Dock Mic A, 1st or 48kHz only */
#define EMU_SRC_DOCK_MIC_A2 0x0101 /* Audio Dock Mic A, 2nd or 96kHz */
#define EMU_SRC_DOCK_MIC_A3 0x0102 /* Audio Dock Mic A, 3rd or 192kHz */
#define EMU_SRC_DOCK_MIC_A4 0x0103 /* Audio Dock Mic A, 4th or 192kHz */
#define EMU_SRC_DOCK_MIC_B1 0x0104 /* Audio Dock Mic B, 1st or 48kHz only */
#define EMU_SRC_DOCK_MIC_B2 0x0105 /* Audio Dock Mic B, 2nd or 96kHz */
#define EMU_SRC_DOCK_MIC_B3 0x0106 /* Audio Dock Mic B, 3rd or 192kHz */
#define EMU_SRC_DOCK_MIC_B4 0x0107 /* Audio Dock Mic B, 4th or 192kHz */
#define EMU_SRC_DOCK_ADC1_LEFT1 0x0108 /* Audio Dock ADC1 Left, 1st or 48kHz only */
#define EMU_SRC_DOCK_ADC1_LEFT2 0x0109 /* Audio Dock ADC1 Left, 2nd or 96kHz */
#define EMU_SRC_DOCK_ADC1_LEFT3 0x010a /* Audio Dock ADC1 Left, 3rd or 192kHz */
#define EMU_SRC_DOCK_ADC1_LEFT4 0x010b /* Audio Dock ADC1 Left, 4th or 192kHz */
#define EMU_SRC_DOCK_ADC1_RIGHT1 0x010c /* Audio Dock ADC1 Right, 1st or 48kHz only */
#define EMU_SRC_DOCK_ADC1_RIGHT2 0x010d /* Audio Dock ADC1 Right, 2nd or 96kHz */
#define EMU_SRC_DOCK_ADC1_RIGHT3 0x010e /* Audio Dock ADC1 Right, 3rd or 192kHz */
#define EMU_SRC_DOCK_ADC1_RIGHT4 0x010f /* Audio Dock ADC1 Right, 4th or 192kHz */
#define EMU_SRC_DOCK_ADC2_LEFT1 0x0110 /* Audio Dock ADC2 Left, 1st or 48kHz only */
#define EMU_SRC_DOCK_ADC2_LEFT2 0x0111 /* Audio Dock ADC2 Left, 2nd or 96kHz */
#define EMU_SRC_DOCK_ADC2_LEFT3 0x0112 /* Audio Dock ADC2 Left, 3rd or 192kHz */
#define EMU_SRC_DOCK_ADC2_LEFT4 0x0113 /* Audio Dock ADC2 Left, 4th or 192kHz */
#define EMU_SRC_DOCK_ADC2_RIGHT1 0x0114 /* Audio Dock ADC2 Right, 1st or 48kHz only */
#define EMU_SRC_DOCK_ADC2_RIGHT2 0x0115 /* Audio Dock ADC2 Right, 2nd or 96kHz */
#define EMU_SRC_DOCK_ADC2_RIGHT3 0x0116 /* Audio Dock ADC2 Right, 3rd or 192kHz */
#define EMU_SRC_DOCK_ADC2_RIGHT4 0x0117 /* Audio Dock ADC2 Right, 4th or 192kHz */
#define EMU_SRC_DOCK_ADC3_LEFT1 0x0118 /* Audio Dock ADC3 Left, 1st or 48kHz only */
#define EMU_SRC_DOCK_ADC3_LEFT2 0x0119 /* Audio Dock ADC3 Left, 2nd or 96kHz */
#define EMU_SRC_DOCK_ADC3_LEFT3 0x011a /* Audio Dock ADC3 Left, 3rd or 192kHz */
#define EMU_SRC_DOCK_ADC3_LEFT4 0x011b /* Audio Dock ADC3 Left, 4th or 192kHz */
#define EMU_SRC_DOCK_ADC3_RIGHT1 0x011c /* Audio Dock ADC3 Right, 1st or 48kHz only */
#define EMU_SRC_DOCK_ADC3_RIGHT2 0x011d /* Audio Dock ADC3 Right, 2nd or 96kHz */
#define EMU_SRC_DOCK_ADC3_RIGHT3 0x011e /* Audio Dock ADC3 Right, 3rd or 192kHz */
#define EMU_SRC_DOCK_ADC3_RIGHT4 0x011f /* Audio Dock ADC3 Right, 4th or 192kHz */
#define EMU_SRC_HAMOA_ADC_LEFT1 0x0200 /* Hamoa ADC Left, 1st or 48kHz only */
#define EMU_SRC_HAMOA_ADC_LEFT2 0x0202 /* Hamoa ADC Left, 2nd or 96kHz */
#define EMU_SRC_HAMOA_ADC_LEFT3 0x0204 /* Hamoa ADC Left, 3rd or 192kHz */
#define EMU_SRC_HAMOA_ADC_LEFT4 0x0206 /* Hamoa ADC Left, 4th or 192kHz */
#define EMU_SRC_HAMOA_ADC_RIGHT1 0x0201 /* Hamoa ADC Right, 1st or 48kHz only */
#define EMU_SRC_HAMOA_ADC_RIGHT2 0x0203 /* Hamoa ADC Right, 2nd or 96kHz */
#define EMU_SRC_HAMOA_ADC_RIGHT3 0x0205 /* Hamoa ADC Right, 3rd or 192kHz */
#define EMU_SRC_HAMOA_ADC_RIGHT4 0x0207 /* Hamoa ADC Right, 4th or 192kHz */
#define EMU_SRC_ALICE_EMU32A 0x0300 /* Alice2 EMU32a 16 outputs. +0 to +0xf */
#define EMU_SRC_ALICE_EMU32B 0x0310 /* Alice2 EMU32b 16 outputs. +0 to +0xf */
#define EMU_SRC_HANA_ADAT 0x0400 /* Hana ADAT 8 channel in +0 to +7 */
#define EMU_SRC_HANA_SPDIF_LEFT1 0x0500 /* Hana SPDIF Left, 1st or 48kHz only */
#define EMU_SRC_HANA_SPDIF_LEFT2 0x0502 /* Hana SPDIF Left, 2nd or 96kHz */
#define EMU_SRC_HANA_SPDIF_RIGHT1 0x0501 /* Hana SPDIF Right, 1st or 48kHz only */
#define EMU_SRC_HANA_SPDIF_RIGHT2 0x0503 /* Hana SPDIF Right, 2nd or 96kHz */
/* Additional inputs for 1616(M)/Microdock */
/* Microdock S/PDIF Left, 1st or 48kHz only */
#define EMU_SRC_MDOCK_SPDIF_LEFT1 0x0112
/* Microdock S/PDIF Left, 2nd or 96kHz */
#define EMU_SRC_MDOCK_SPDIF_LEFT2 0x0113
/* Microdock S/PDIF Right, 1st or 48kHz only */
#define EMU_SRC_MDOCK_SPDIF_RIGHT1 0x0116
/* Microdock S/PDIF Right, 2nd or 96kHz */
#define EMU_SRC_MDOCK_SPDIF_RIGHT2 0x0117
/* Microdock ADAT 8 channel in +8 to +f */
#define EMU_SRC_MDOCK_ADAT 0x0118
/* 0x600 and 0x700 no used */
/* ------------------- STRUCTURES -------------------- */
enum {
EMU10K1_EFX,
EMU10K1_PCM,
EMU10K1_SYNTH,
EMU10K1_MIDI
};
struct snd_emu10k1;
struct snd_emu10k1_voice {
struct snd_emu10k1 *emu;
int number;
unsigned int use: 1,
pcm: 1,
efx: 1,
synth: 1,
midi: 1;
void (*interrupt)(struct snd_emu10k1 *emu, struct snd_emu10k1_voice *pvoice);
struct snd_emu10k1_pcm *epcm;
};
enum {
PLAYBACK_EMUVOICE,
PLAYBACK_EFX,
CAPTURE_AC97ADC,
CAPTURE_AC97MIC,
CAPTURE_EFX
};
struct snd_emu10k1_pcm {
struct snd_emu10k1 *emu;
int type;
struct snd_pcm_substream *substream;
struct snd_emu10k1_voice *voices[NUM_EFX_PLAYBACK];
struct snd_emu10k1_voice *extra;
unsigned short running;
unsigned short first_ptr;
struct snd_util_memblk *memblk;
unsigned int start_addr;
unsigned int ccca_start_addr;
unsigned int capture_ipr; /* interrupt acknowledge mask */
unsigned int capture_inte; /* interrupt enable mask */
unsigned int capture_ba_reg; /* buffer address register */
unsigned int capture_bs_reg; /* buffer size register */
unsigned int capture_idx_reg; /* buffer index register */
unsigned int capture_cr_val; /* control value */
unsigned int capture_cr_val2; /* control value2 (for audigy) */
unsigned int capture_bs_val; /* buffer size value */
unsigned int capture_bufsize; /* buffer size in bytes */
};
struct snd_emu10k1_pcm_mixer {
/* mono, left, right x 8 sends (4 on emu10k1) */
unsigned char send_routing[3][8];
unsigned char send_volume[3][8];
unsigned short attn[3];
struct snd_emu10k1_pcm *epcm;
};
#define snd_emu10k1_compose_send_routing(route) \
((route[0] | (route[1] << 4) | (route[2] << 8) | (route[3] << 12)) << 16)
#define snd_emu10k1_compose_audigy_fxrt1(route) \
((unsigned int)route[0] | ((unsigned int)route[1] << 8) | ((unsigned int)route[2] << 16) | ((unsigned int)route[3] << 24))
#define snd_emu10k1_compose_audigy_fxrt2(route) \
((unsigned int)route[4] | ((unsigned int)route[5] << 8) | ((unsigned int)route[6] << 16) | ((unsigned int)route[7] << 24))
struct snd_emu10k1_memblk {
struct snd_util_memblk mem;
/* private part */
int first_page, last_page, pages, mapped_page;
unsigned int map_locked;
struct list_head mapped_link;
struct list_head mapped_order_link;
};
#define snd_emu10k1_memblk_offset(blk) (((blk)->mapped_page << PAGE_SHIFT) | ((blk)->mem.offset & (PAGE_SIZE - 1)))
#define EMU10K1_MAX_TRAM_BLOCKS_PER_CODE 16
struct snd_emu10k1_fx8010_ctl {
struct list_head list; /* list link container */
unsigned int vcount;
unsigned int count; /* count of GPR (1..16) */
unsigned short gpr[32]; /* GPR number(s) */
unsigned int value[32];
unsigned int min; /* minimum range */
unsigned int max; /* maximum range */
unsigned int translation; /* translation type (EMU10K1_GPR_TRANSLATION*) */
struct snd_kcontrol *kcontrol;
};
typedef void (snd_fx8010_irq_handler_t)(struct snd_emu10k1 *emu, void *private_data);
struct snd_emu10k1_fx8010_irq {
struct snd_emu10k1_fx8010_irq *next;
snd_fx8010_irq_handler_t *handler;
unsigned short gpr_running;
void *private_data;
};
struct snd_emu10k1_fx8010_pcm {
unsigned int valid: 1,
opened: 1,
active: 1;
unsigned int channels; /* 16-bit channels count */
unsigned int tram_start; /* initial ring buffer position in TRAM (in samples) */
unsigned int buffer_size; /* count of buffered samples */
unsigned short gpr_size; /* GPR containing size of ring buffer in samples (host) */
unsigned short gpr_ptr; /* GPR containing current pointer in the ring buffer (host = reset, FX8010) */
unsigned short gpr_count; /* GPR containing count of samples between two interrupts (host) */
unsigned short gpr_tmpcount; /* GPR containing current count of samples to interrupt (host = set, FX8010) */
unsigned short gpr_trigger; /* GPR containing trigger (activate) information (host) */
unsigned short gpr_running; /* GPR containing info if PCM is running (FX8010) */
unsigned char etram[32]; /* external TRAM address & data */
struct snd_pcm_indirect pcm_rec;
unsigned int tram_pos;
unsigned int tram_shift;
struct snd_emu10k1_fx8010_irq irq;
};
struct snd_emu10k1_fx8010 {
unsigned short fxbus_mask; /* used FX buses (bitmask) */
unsigned short extin_mask; /* used external inputs (bitmask) */
unsigned short extout_mask; /* used external outputs (bitmask) */
unsigned short pad1;
unsigned int itram_size; /* internal TRAM size in samples */
struct snd_dma_buffer etram_pages; /* external TRAM pages and size */
unsigned int dbg; /* FX debugger register */
unsigned char name[128];
int gpr_size; /* size of allocated GPR controls */
int gpr_count; /* count of used kcontrols */
struct list_head gpr_ctl; /* GPR controls */
struct mutex lock;
struct snd_emu10k1_fx8010_pcm pcm[8];
spinlock_t irq_lock;
struct snd_emu10k1_fx8010_irq *irq_handlers;
};
struct snd_emu10k1_midi {
struct snd_emu10k1 *emu;
struct snd_rawmidi *rmidi;
struct snd_rawmidi_substream *substream_input;
struct snd_rawmidi_substream *substream_output;
unsigned int midi_mode;
spinlock_t input_lock;
spinlock_t output_lock;
spinlock_t open_lock;
int tx_enable, rx_enable;
int port;
int ipr_tx, ipr_rx;
void (*interrupt)(struct snd_emu10k1 *emu, unsigned int status);
};
enum {
EMU_MODEL_SB,
EMU_MODEL_EMU1010,
EMU_MODEL_EMU1010B,
EMU_MODEL_EMU1616,
EMU_MODEL_EMU0404,
};
struct snd_emu_chip_details {
u32 vendor;
u32 device;
u32 subsystem;
unsigned char revision;
unsigned char emu10k1_chip; /* Original SB Live. Not SB Live 24bit. */
unsigned char emu10k2_chip; /* Audigy 1 or Audigy 2. */
unsigned char ca0102_chip; /* Audigy 1 or Audigy 2. Not SB Audigy 2 Value. */
unsigned char ca0108_chip; /* Audigy 2 Value */
unsigned char ca_cardbus_chip; /* Audigy 2 ZS Notebook */
unsigned char ca0151_chip; /* P16V */
unsigned char spk71; /* Has 7.1 speakers */
unsigned char sblive51; /* SBLive! 5.1 - extout 0x11 -> center, 0x12 -> lfe */
unsigned char spdif_bug; /* Has Spdif phasing bug */
unsigned char ac97_chip; /* Has an AC97 chip: 1 = mandatory, 2 = optional */
unsigned char ecard; /* APS EEPROM */
unsigned char emu_model; /* EMU model type */
unsigned char spi_dac; /* SPI interface for DAC */
unsigned char i2c_adc; /* I2C interface for ADC */
unsigned char adc_1361t; /* Use Philips 1361T ADC */
unsigned char invert_shared_spdif; /* analog/digital switch inverted */
const char *driver;
const char *name;
const char *id; /* for backward compatibility - can be NULL if not needed */
};
struct snd_emu1010 {
unsigned int output_source[64];
unsigned int input_source[64];
unsigned int adc_pads; /* bit mask */
unsigned int dac_pads; /* bit mask */
unsigned int internal_clock; /* 44100 or 48000 */
unsigned int optical_in; /* 0:SPDIF, 1:ADAT */
unsigned int optical_out; /* 0:SPDIF, 1:ADAT */
struct delayed_work firmware_work;
u32 last_reg;
};
struct snd_emu10k1 {
int irq;
unsigned long port; /* I/O port number */
unsigned int tos_link: 1, /* tos link detected */
rear_ac97: 1, /* rear channels are on AC'97 */
enable_ir: 1;
unsigned int support_tlv :1;
/* Contains profile of card capabilities */
const struct snd_emu_chip_details *card_capabilities;
unsigned int audigy; /* is Audigy? */
unsigned int revision; /* chip revision */
unsigned int serial; /* serial number */
unsigned short model; /* subsystem id */
unsigned int card_type; /* EMU10K1_CARD_* */
unsigned int ecard_ctrl; /* ecard control bits */
unsigned int address_mode; /* address mode */
unsigned long dma_mask; /* PCI DMA mask */
bool iommu_workaround; /* IOMMU workaround needed */
unsigned int delay_pcm_irq; /* in samples */
int max_cache_pages; /* max memory size / PAGE_SIZE */
struct snd_dma_buffer silent_page; /* silent page */
struct snd_dma_buffer ptb_pages; /* page table pages */
struct snd_dma_device p16v_dma_dev;
struct snd_dma_buffer *p16v_buffer;
struct snd_util_memhdr *memhdr; /* page allocation list */
struct list_head mapped_link_head;
struct list_head mapped_order_link_head;
void **page_ptr_table;
unsigned long *page_addr_table;
spinlock_t memblk_lock;
unsigned int spdif_bits[3]; /* s/pdif out setup */
unsigned int i2c_capture_source;
u8 i2c_capture_volume[4][2];
struct snd_emu10k1_fx8010 fx8010; /* FX8010 info */
int gpr_base;
struct snd_ac97 *ac97;
struct pci_dev *pci;
struct snd_card *card;
struct snd_pcm *pcm;
struct snd_pcm *pcm_mic;
struct snd_pcm *pcm_efx;
struct snd_pcm *pcm_multi;
struct snd_pcm *pcm_p16v;
spinlock_t synth_lock;
void *synth;
int (*get_synth_voice)(struct snd_emu10k1 *emu);
spinlock_t reg_lock;
spinlock_t emu_lock;
spinlock_t voice_lock;
spinlock_t spi_lock; /* serialises access to spi port */
spinlock_t i2c_lock; /* serialises access to i2c port */
struct snd_emu10k1_voice voices[NUM_G];
struct snd_emu10k1_voice p16v_voices[4];
struct snd_emu10k1_voice p16v_capture_voice;
int p16v_device_offset;
u32 p16v_capture_source;
u32 p16v_capture_channel;
struct snd_emu1010 emu1010;
struct snd_emu10k1_pcm_mixer pcm_mixer[32];
struct snd_emu10k1_pcm_mixer efx_pcm_mixer[NUM_EFX_PLAYBACK];
struct snd_kcontrol *ctl_send_routing;
struct snd_kcontrol *ctl_send_volume;
struct snd_kcontrol *ctl_attn;
struct snd_kcontrol *ctl_efx_send_routing;
struct snd_kcontrol *ctl_efx_send_volume;
struct snd_kcontrol *ctl_efx_attn;
void (*hwvol_interrupt)(struct snd_emu10k1 *emu, unsigned int status);
void (*capture_interrupt)(struct snd_emu10k1 *emu, unsigned int status);
void (*capture_mic_interrupt)(struct snd_emu10k1 *emu, unsigned int status);
void (*capture_efx_interrupt)(struct snd_emu10k1 *emu, unsigned int status);
void (*spdif_interrupt)(struct snd_emu10k1 *emu, unsigned int status);
void (*dsp_interrupt)(struct snd_emu10k1 *emu);
struct snd_pcm_substream *pcm_capture_substream;
struct snd_pcm_substream *pcm_capture_mic_substream;
struct snd_pcm_substream *pcm_capture_efx_substream;
struct snd_pcm_substream *pcm_playback_efx_substream;
struct snd_timer *timer;
struct snd_emu10k1_midi midi;
struct snd_emu10k1_midi midi2; /* for audigy */
unsigned int efx_voices_mask[2];
unsigned int next_free_voice;
const struct firmware *firmware;
const struct firmware *dock_fw;
#ifdef CONFIG_PM_SLEEP
unsigned int *saved_ptr;
unsigned int *saved_gpr;
unsigned int *tram_val_saved;
unsigned int *tram_addr_saved;
unsigned int *saved_icode;
unsigned int *p16v_saved;
unsigned int saved_a_iocfg, saved_hcfg;
bool suspend;
#endif
};
int snd_emu10k1_create(struct snd_card *card,
struct pci_dev *pci,
unsigned short extin_mask,
unsigned short extout_mask,
long max_cache_bytes,
int enable_ir,
uint subsystem);
int snd_emu10k1_pcm(struct snd_emu10k1 *emu, int device);
int snd_emu10k1_pcm_mic(struct snd_emu10k1 *emu, int device);
int snd_emu10k1_pcm_efx(struct snd_emu10k1 *emu, int device);
int snd_p16v_pcm(struct snd_emu10k1 *emu, int device);
int snd_p16v_mixer(struct snd_emu10k1 * emu);
int snd_emu10k1_pcm_multi(struct snd_emu10k1 *emu, int device);
int snd_emu10k1_fx8010_pcm(struct snd_emu10k1 *emu, int device);
int snd_emu10k1_mixer(struct snd_emu10k1 * emu, int pcm_device, int multi_device);
int snd_emu10k1_timer(struct snd_emu10k1 * emu, int device);
int snd_emu10k1_fx8010_new(struct snd_emu10k1 *emu, int device);
irqreturn_t snd_emu10k1_interrupt(int irq, void *dev_id);
void snd_emu10k1_voice_init(struct snd_emu10k1 * emu, int voice);
int snd_emu10k1_init_efx(struct snd_emu10k1 *emu);
void snd_emu10k1_free_efx(struct snd_emu10k1 *emu);
int snd_emu10k1_fx8010_tram_setup(struct snd_emu10k1 *emu, u32 size);
int snd_emu10k1_done(struct snd_emu10k1 * emu);
/* I/O functions */
unsigned int snd_emu10k1_ptr_read(struct snd_emu10k1 * emu, unsigned int reg, unsigned int chn);
void snd_emu10k1_ptr_write(struct snd_emu10k1 *emu, unsigned int reg, unsigned int chn, unsigned int data);
unsigned int snd_emu10k1_ptr20_read(struct snd_emu10k1 * emu, unsigned int reg, unsigned int chn);
void snd_emu10k1_ptr20_write(struct snd_emu10k1 *emu, unsigned int reg, unsigned int chn, unsigned int data);
int snd_emu10k1_spi_write(struct snd_emu10k1 * emu, unsigned int data);
int snd_emu10k1_i2c_write(struct snd_emu10k1 *emu, u32 reg, u32 value);
int snd_emu1010_fpga_write(struct snd_emu10k1 * emu, u32 reg, u32 value);
int snd_emu1010_fpga_read(struct snd_emu10k1 * emu, u32 reg, u32 *value);
int snd_emu1010_fpga_link_dst_src_write(struct snd_emu10k1 * emu, u32 dst, u32 src);
unsigned int snd_emu10k1_efx_read(struct snd_emu10k1 *emu, unsigned int pc);
void snd_emu10k1_intr_enable(struct snd_emu10k1 *emu, unsigned int intrenb);
void snd_emu10k1_intr_disable(struct snd_emu10k1 *emu, unsigned int intrenb);
void snd_emu10k1_voice_intr_enable(struct snd_emu10k1 *emu, unsigned int voicenum);
void snd_emu10k1_voice_intr_disable(struct snd_emu10k1 *emu, unsigned int voicenum);
void snd_emu10k1_voice_intr_ack(struct snd_emu10k1 *emu, unsigned int voicenum);
void snd_emu10k1_voice_half_loop_intr_enable(struct snd_emu10k1 *emu, unsigned int voicenum);
void snd_emu10k1_voice_half_loop_intr_disable(struct snd_emu10k1 *emu, unsigned int voicenum);
void snd_emu10k1_voice_half_loop_intr_ack(struct snd_emu10k1 *emu, unsigned int voicenum);
void snd_emu10k1_voice_set_loop_stop(struct snd_emu10k1 *emu, unsigned int voicenum);
void snd_emu10k1_voice_clear_loop_stop(struct snd_emu10k1 *emu, unsigned int voicenum);
void snd_emu10k1_wait(struct snd_emu10k1 *emu, unsigned int wait);
static inline unsigned int snd_emu10k1_wc(struct snd_emu10k1 *emu) { return (inl(emu->port + WC) >> 6) & 0xfffff; }
unsigned short snd_emu10k1_ac97_read(struct snd_ac97 *ac97, unsigned short reg);
void snd_emu10k1_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short data);
unsigned int snd_emu10k1_rate_to_pitch(unsigned int rate);
#ifdef CONFIG_PM_SLEEP
void snd_emu10k1_suspend_regs(struct snd_emu10k1 *emu);
void snd_emu10k1_resume_init(struct snd_emu10k1 *emu);
void snd_emu10k1_resume_regs(struct snd_emu10k1 *emu);
int snd_emu10k1_efx_alloc_pm_buffer(struct snd_emu10k1 *emu);
void snd_emu10k1_efx_free_pm_buffer(struct snd_emu10k1 *emu);
void snd_emu10k1_efx_suspend(struct snd_emu10k1 *emu);
void snd_emu10k1_efx_resume(struct snd_emu10k1 *emu);
int snd_p16v_alloc_pm_buffer(struct snd_emu10k1 *emu);
void snd_p16v_free_pm_buffer(struct snd_emu10k1 *emu);
void snd_p16v_suspend(struct snd_emu10k1 *emu);
void snd_p16v_resume(struct snd_emu10k1 *emu);
#endif
/* memory allocation */
struct snd_util_memblk *snd_emu10k1_alloc_pages(struct snd_emu10k1 *emu, struct snd_pcm_substream *substream);
int snd_emu10k1_free_pages(struct snd_emu10k1 *emu, struct snd_util_memblk *blk);
int snd_emu10k1_alloc_pages_maybe_wider(struct snd_emu10k1 *emu, size_t size,
struct snd_dma_buffer *dmab);
struct snd_util_memblk *snd_emu10k1_synth_alloc(struct snd_emu10k1 *emu, unsigned int size);
int snd_emu10k1_synth_free(struct snd_emu10k1 *emu, struct snd_util_memblk *blk);
int snd_emu10k1_synth_bzero(struct snd_emu10k1 *emu, struct snd_util_memblk *blk, int offset, int size);
int snd_emu10k1_synth_copy_from_user(struct snd_emu10k1 *emu, struct snd_util_memblk *blk, int offset, const char __user *data, int size);
int snd_emu10k1_memblk_map(struct snd_emu10k1 *emu, struct snd_emu10k1_memblk *blk);
/* voice allocation */
int snd_emu10k1_voice_alloc(struct snd_emu10k1 *emu, int type, int pair, struct snd_emu10k1_voice **rvoice);
int snd_emu10k1_voice_free(struct snd_emu10k1 *emu, struct snd_emu10k1_voice *pvoice);
/* MIDI uart */
int snd_emu10k1_midi(struct snd_emu10k1 * emu);
int snd_emu10k1_audigy_midi(struct snd_emu10k1 * emu);
/* proc interface */
int snd_emu10k1_proc_init(struct snd_emu10k1 * emu);
/* fx8010 irq handler */
int snd_emu10k1_fx8010_register_irq_handler(struct snd_emu10k1 *emu,
snd_fx8010_irq_handler_t *handler,
unsigned char gpr_running,
void *private_data,
struct snd_emu10k1_fx8010_irq *irq);
int snd_emu10k1_fx8010_unregister_irq_handler(struct snd_emu10k1 *emu,
struct snd_emu10k1_fx8010_irq *irq);
#endif /* __SOUND_EMU10K1_H */
OHA YOOOO